Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Dear Nordic Team,
on my board with NRF85240 High Voltage mode is used. Accordingly to datasheet (5.3.8.2 Regulator Specifications, REG0 stage), in this mode the following...
Can you help with why I get this serial debug message when trying to start Headset nrf5340_Audio DK in DFU mode
HR [00:00:02.068,450] <err> dfu: SMP_SVR Advertising failed...
Hi!
I have an issue with control of the MAGPIO during RFTEST procedures.
The device is using RF Switch (like Thingy91) and I want to perform SNR/Received signal power...
Hello All,
Hoping to hear your opinion as I have little experience on how reliably the following would work.
The device should count pulses or edges from a reed switch...
Hi,
I'm using a Thingy:53 for some prototyping work. The device is configured with the standard USB CDC ACM as logging backend and I use pyserial-miniterm to access the...
Hello All,
I hope all is well. I have now been using Nordic ICs for close to 10 years and have become familiar with SDK5 and developed multiple applications using it....
Hello,
I would like to fast adc some analog signal from my opamp PCB. I am using nrf5340DK SDK1.9.1 with VS Code.
Got the example code nrfx_saadc.zip from and my first...
Hi,
I'm using the following function in my project, in order to get an idea of how much memory can be reserved with malloc :
This function should return the last value...
Hello,
I have a question about the Kconfig extension for VSCode.
When I use the nrf52840 DK, the Board Selection correctly check the nrf52840dk_nrf52840 and all the configs...
I've been continuing to work on why my power level seemed low after getting the Skyworks FEM in my Fanstel BT840x module going, per this thread:
So far, I've been setting...
I want to increase the rate of data from UARTE to RF FIFO.Can data be transferred from the cache to the RF FIFO using DMA?
nrf52832 nRF5_SDK_17.1.0_ddde560 S132
Hello, I am trying to understand the adc example using the PCA10056.
HI can see the following code that initializes 3 `zephyr_user` channels
In the DT file,...
Hi,
I recently went through the manual installation instructions for the nRF Connect SDK posted here ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/gs_installing...
