Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Hallo,
I am currently trying to debug the Matter samples on the NRF5340 DK. They all work fine, but I have a problem with the "Thread Viewer" in VS Code while debugging...
I have cypress ble module that generates carrier with PRBS9 modulation and GFSK on 2408MHz. As a receiver I use nrf52 Dongle and nrf52 DK board. In RSSI viewer I can see signal...
Hello Before we just have to overwrite shouldAutoConnect to enable an automatic reconnection Is autoconnect supported on Android NRF toolbox 3.1.3 (kotlin implementation)...
Hello,
In order to reduce the consumption, I remove some sensors (physically from the board).
Should I change the SW ? Is there any discovery state required that should...
Hi Nordic,
1. I am using bl653_dvk board and (C:\ncs\v2.1.0-rc2\zephyr\samples\drivers\uart\echo_bot) is using for my sample
2. Here is i need to communicate with both...
Good day
sorry if it's not clear, it's a rare problem and I have difficulties to explain it but here goes:
I Have two boards - PCA10056 from nordic and nrf52840 Feather...
Hello,
We have a custom NRF52840 board that can be powered via both Battery and USB. The peripherals that are connected to the board require it to be in high power mode...
Hi,
Build an application without SD but with MBR. MBR is at address 0x0000 - 0x1000. Application is at 0x1000 - 0xF0000. At the beginning of the application is the ISR...
Hi
What is your maximum throughput experienced with Android devices over Bluetooth 5.0+?
On my side, I can reach 340 kbps from Android to a nrf52 based device while transferring...
Hello all,
Two same same nRF52820 modules are connected to two usb ports and they are easily flashed via Segger, namely selected via two JLink emulator numbers.
Two separate...
Dear sir/madam,
My question is: - can you recommend courses/books which can help us to more deeply understand the zephyr RTOS in conjunction with the nordic microcontroller...
Hi,
We are currently developing the nRF52833 (peripheral) with ncs v2.0.0. We would like to calculate the link budget of our system when different smartphones are used as...
Hello
I am working with nrf9160dk_nrf52840 and using the BLE of nrf52
I am using the peripheral uart sample code to send some custom data.
I am trying to send more than...
I am having trouble updating a product with the firmware update file using NRFconnect app for ios version 2.5.3 using iphone se 2020.
We have been running successful updates...
