Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,
I am using the NRF9160 DK to try the NRF9160 with AWS IOT.. I have experience with making ESP32 work with AWS IOT but i cant say the same for this controller. ...
Does the modem firmware revert to using TLSv1 on a failure to connect? I'm getting some occasional weirdness connecting to an OpenSSL based server:
It works most of the...
Hi,
I'm working on project where I want to scan nearby beacons while participating in a Mesh network. I've configured everything as shown in the sample ble peripheral lbs...
Hi,
I am working with an nRF52832 in the nRF52-DK. I am trying to use the ADC with timers through PPI. I have a timer with five CC events, and one of them through ADC measurements...
I am attempting to establish a PPP connection between an nRF9160 and a Linux device over a UART (hardware flow control is optional). The goal is to allow these devices to...
Hi,
When applying for the SUPL client library i get the error message: "your application for SUPL-C license hase been denied"
I have an active DevZone account
I applied...
I have my code working correctly and for site testing of the first 20 units the customer wants to know the
MAC address so that any glitches can be identified to a particular...
Hi,
we would like to use nRF Desktop to test throughput and show we can send 20B per ms (from peripheral to central).
The LLPM sample is not well optimized, while nRF...
Hello,
Using the nRF Connect SDK 1.9.1 for nRF9160 location. Found the "location" library quite simple and scalable to use. So was looking into it. We do not plan to use...
I bought a PPK (not the PPK2) a while ago, and it's been working fine. However, recently it stopped working. I'm using a JLink EDU mini, and the power profiler app in nrfconnect...
Hi, I'm developing an application using Libuartes to handle GPS data 1. According my knowledge about Libuartes, It will call the NRF_LIBUARTE_ASYNC_EVT_RX_DATA when the buffer...
Hi,
Since BLE advertising consumes current, I want to stop sampling ADC data during BLE is advertising. Are there any BLE events to know when advertising happens or are...
I use the zephyr version 3.0.9 for DF.i use the both boards nrf52833dk.i set the antenna array including antenna_num,antenna_patterns,and antenna_ref(pdu_antenna).
both...
Hello,
NCS1.9.1, VSCode, nRF5340DK, periodic_adv
CONFIG_BT_DEVICE_NAME="xxx" in file prj.conf.
how to dynamic change BT_DEVICE_NAME in main() start?
Best rega...
