Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
from the datasheet we see that this device can operate at 1.8V or 3V3 (or anything in between).
We can also check supply current on the mRF52DK which runs at 3V3.
How...
Hi everyone,
I would like to measure the total current consumption of the board in order to get an estimation of the battery life. I am using PPK-2 and nRF Connect Power...
Hello Everyone,
For my project, I have to make my BLE device to advertise itself for a period of time and transit to "scan" mode to scan for other device for a period of...
I am getting this fault when i try to run a observer handler where i have implemented semaphores.
And i cant figure out what this error code means
Thanks in advan...
Hello,
I am currently trying to run this ble_secure_bootloader . I am using SES V5.68 with the nRF52840 SoC and I am using nRF5 SDK version 14.2.0. I have also adjusted...
Hi Team,
I want to know the time with time resolution milliseconds for initialization time of nrf52840 chips and nrf52840 DK with external supply model?
KInd regards,...
Hi,
The below code I believe is in error. The below write operation overwrites the LIO2, LIO3, WIPWAIT, and WREN settings in the CINSTRCONF register by only writing the...
First off, It's great you guys are setting a high pace with development and improving the SDK but I and I think many other people would like it if you change a full version...
Hi!
I am currently working on this sample with an nrf52840 board and a nrf52832 board:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/peripheral...
Hi All!
Hope you are doing well! I am using nrf52840 and nrf58233. Is there any example available for both transmitter and receiver for connectable coded PHY beacons?...
I am trying to determine the best way to debounce 7 digital inputs with 2 bounce times ranging between 50 ms to 2 seconds. I thought of using the GPIOTE but that seems to...
Hi All,
I asked this question before but I accidentally pressed close.
The engineer told me that f or nRF5 SDK ( I assume as you said Segger), you can send 10 byte long...
I'm working with the project based on nrf52833 and SDK 17. I've noticed that when there are no devices on I2C bus, the application stucks on nrf_drv_twi_tx function, and the...
Hi , I'm using nrf5340 and nrf connect sdk 1.5.1 , recently I found out when sending large amount of data with low RSSI through bt_gatt_notify_cb the system would enter some...
