Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Hi,
it seems like I'm struggling with issue mentioned here: https://infocenter.nordicsemi.com/pdf/nRF52832_Rev_3_Errata_v1.0.pdf#%5B%7B%22num%22%3A431%2C%22gen%22%3A0%7D...
Hi support Team,
I create custom ble-service with help of example project ble_app_att_mtu_throughput (nRF5_SDK_17.0.2)its working successfully.Now i need to add security...
Hello,
I am modifying mqtt_simple example to send float over mqtt.
If I change %f to %d, it works without crash.
I have tried enable/disable FPU or increasing HEAP_MEM_POOL_SIZE...
I have nrf52840-dk board. i tried the UART example from the peripherals directory. it works with the default UART Configuration pins.
problem started when i tried to change...
Hi,
I have a configuration of five nRF52840 custom devices transmitting sensor data to a central device (laptop)
The devices can be connected and send data to the central...
I would like to use an external clock for the nrf5340.
The documentation indicates that it is posible override the LFCLK control system to set another source by writing...
hy, i have a problem wit undefine simbol, how to define the simbol, i laready add related path folder that contain the undefine simbol target, but this error still appear...
Segger SEGGER_RTT.c $Rev: 24766. (really 5 digits!) The version in nRF5_SDK_17.2.0.d674dde/ $Rev: 6852 is quite old
PS How can I use a tag not listed? like Segger ?
PPS...
I have the following pm_static.yml defined for my project (nrf52840 on a custom board, NCS v1.7-branch):
west build -t partition_manager_report shows this is working as...
Hi,
I am searching for some methods to blocking the abnormal PCBAs which got short-circuit in DCC and DEC4 after SMT process. These abnormal PCBAs will cause BT pairing...
Hi
HI, I have developed an application for the nRF5232, using NCS 1.7.0. so i need to add the external flash.
I would need a working example running OTA with external...
The objective is to be able to send data back up to an MQTT server using the Nordic NRF9160 hardware. Nordic staff is helpful but only writes back usually in the very early...
I am using modem firmware v1.2.3 and NCS v1.6.0. Event GPS_EVT_SEARCH_TIMEOUT never occurs despite setting fix retry time to non-zero value. I am using GPS driver (no new...
