Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
I am using nRF52832 with nRF52 SDK 17
My application consists of two timers running every 5 seconds and every 35 ms. After some very long time and only with a few units...
Hi Nordic,
I've been trying to run examples developed for the PCA10059 for several days now without success.
I changed the Preprocessor Definition from BOARD_PCA10056...
Hello,
I am trying to create a custom driver for an accelerometer I have sourced. I am using the nrf5340-dk.
The code was not able to compile as a result of the following...
Following function implementation is not following POSIX documentation specified at https://pubs.opengroup.org/onlinepubs/9699919799/functions/getaddrinfo.html, which says...
Hello Nordic Semi
I know that nrf52832 does not support SPH0645 Mic on I2S interface because of data width limitation in hardware for nrf52832.
I want to know that does...
Hello,
I'm using the mqtt_simple example with the following changes to add WebSockets Secure Support:
Also I set the Application MQTT topics, clientId, host, port...
Hi,
I have multiple devices that support Nordic DFU.
I want to update them using a Linux computer with a bluetooth dongle connected on it (and its not a Nordic Device...
Hi, There,
About the interrupt priority, can I understand it like this? "The two levels: NRF_MESH_IRQ_PRIORITY_LOWEST and NRF_MESH_IRQ_PRIORITY_THREAD have the same functions...
Hi Devzone,
I know that we can adjust "Advertising interval", "Tx power", "Tx payload" to do a power optimization when advertising. But I when I set " Advertising interval...
Hello,
I am trying to decrease the power consumption of my board (nRF52 DK) so that I can only see what's consumed in advertising beacon demo. When I measured the current...
Hi everyone,
I have a board based on thingy91. I have lis2dh and adxl372 sensors on it. They are both connected via SPI, and I've added this to my overlay file:
Also...
Hi,All:
I have finished continuous unmodulated carrier by SD fuctions as below.It is more efficent than DTM examples。But now,I don't know how to ctreat continuous modulated...
Hi,
I would to design a custom PCB with nRF52840 SOC.
I have two different power source:
1. 3V Lithium coin cell
2. 3.7V LiPO battery with charging circuitry
I will...
Hi,
I have a quetion,nRF5340 have two package, so have two diference RF circuit,as below picture,Why are the matching circuits different?
Package is QKAA aQFN94
...
