Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
I use example projects from Nordic Thread: CoAP Client and Thread: CoAP Server with Segger Studio Nordic Edition (projects use Zephry which is generated by NRFConnect...
Hello! I`m developing custom board with NRF52832-QFAA on board and need to use serial bootloader. As in example (secure_dfu_ble_s132_pca10040), I`ve implemented it on board...
Peripheral doesn't have any user interface that can be used for pairing and bonding but I want for my application is that the peripheral gets paired or bonded to the central...
I want to make one mesh beacon as a node of mesh network.
If one mesh beacon is a node of mesh network, I want the beacon broadcast the messages which in mesh network to...
I build some test project in Zephyr examples folder. (ncs\v1.5.1\zephyr\samples\basic\ND_test).
In additional I did some changes in the Zephyr project in drivers and added...
I have recntly purchased a Nordic Semiconductors nrf52840 development board. I am having issues with the J Link OB MSD. When connected to LINUX Ubuntu 20.04 LTS which is running...
Hi,
I am working on a bootloader that can do DFU for my nrf52840 DK. Currently, when the bootloader goes into DFU mode, it obtains the init packet via UART. Then, after...
Hi,
I'm trying to add the secure BLE bootloader(non debug, modified to run with S113, SDK 17.0.2) on a custom board with a nRF52810. I tried to DFU my main application(APP...
i working nrf52832 sdk 16 in that i want to use two uart?
actually nrf52832 have only one hardware interfced UART.but i try to implement two UART1 and UART2 in same program...
Hello,
I am working on an nRF52840 with S140SD chip.
I am currently using the RTT as a backend for logs. I tried adding the Flashlog backend in order to save the logs...
I'm developing with nRF52811 but firmware is developed for nRF52810.
I think there is no difference between them and that firmware should work well.
But SPIS doesn't work...
THis may have an obvious answer to an experienced embedded programmer but I do not qualify to be that. So I have a piece of working code that runs on the nRF52840 DK and it...
Can you use/link both nfc T4T and T2T libraries and wrapper/driver source in same application/build?
I don't mean emulating both modes at the same time.
Thanks.
To the kind attention of Nordic support team,
I have been using nRF ble sniffer successfully, it is a great tool. But I have some troubles when it comes to use it for ble...
