nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
Hello,
I have followed these instructions, but the nRF sniffer option does not show up as an option in the Wireshark GUI, https://infocenter.nordicsemi.com/index.jsp?topic...
Segger cannot seem to find the user included directories. Every time I compile any file I get this error or something similar of {name of file} not found as shown in the pic...
hey
I have worked on BLE, and learned the BLE protocol stack. Now i am learning BLE Mesh. I found the Mesh is also having a stack, I could not understand why both the stacks...
Hallo,
I request for your time and effort to solve the issue that I am facing at the moment. Any suggestions and solutions are highly appreciated.
Hardware: NRF52840DK...
Hello,
It there a download for the nRF-Command-Line-Tools_10_12_2_Installer_64.exe?
I only see a zip file with this and a python setup. I have an internal program...
Hey, I've a string of less than 10 bytes (10 characters max) and I'm establishing the connection between the Central (nRF52833-DK) and the Peripheral (nRF52810) and I've set...
Hello,
We are trying to use the Cryptocell as used in example nrf_crypto_aes_cbc_with_padding along with Secure DFU. However, when the application loads the crypto engine...
DFU secure bootloader ( secure_bootloader/ pca10040_s132_ble ) using segger embedded studio version 5.50
Am using SDK version 17.0.2 for BMD350 nRF52832 module
Already...
Hi there,
I was able to successfully compile and run the "BLE HIDS keyboard" example on my nRF52832 using Segger SES 5.44
My Nordic chip is connected via UART Rx/Tx to...
Good day
I use NRF52840 + SDK v17.0.2. My application relies on _gls example and mainly copies its security settings ( also uses peer manager ) except I use MITM protection...
Hello Dear!
Please look at the red area in the picture.
The C9 820PF, it's no commonly used,We buy it very hard.
Can i modify C9 820PF to change C9 1 nf in desgin?
I've read quite a few threads where people are asking for help getting NAND Flash to work with their devices, only to find out they are not supported. I see that only NOR...
Hi
I am using nrf52832 to develop a ble hid device with tile function
I merge sample code ble_app_tile to ble_app_hid_keyboard example
I use the advertising_init function...
The firmware crashes when passing the ble_stack_init() when the firmware is download but in debug mode it works fine. The screen shots below shows this event.
We are using...
