I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hi,
I'm very new to learn nrf52832. Recently, want to connect my NRF52832 device with pc, then , using the value uploaded from the device to draw a curve in pc' client....
Hello
I'm looking for API example to use Key Management Unit (key storage and key usage). But I didn't find it in all nordic documentation.
Could you help me to use KMU...
I am using the SDK 17.0.2 to make the advertisement and scanning for the two nrf52840 boards. One unit with extended advertisement only on channel 37 and the other unit scan...
The documentation says that: " By default, threads run in supervisor mode and allow access to privileged CPU instructions, the entire memory address space, and peripherals...
Dear Community;
I am trying to send some data via Lora with a nRF9160 connected with SPI to RF95W Lora module. The transmitter is a nRF9160 with a RF95W, and the receiver...
Hello,
We're piloting updating our sensor beacons RuuviTags to use Coded PHY for better range. The current design has nRF52832, our update would be to drop in a nRF52811...
Hi Nordic Support Team,
I am trying to combine
..\nRF5_SDK_17.0.2_d674dde\examples\dfu\secure_bootloader\pca10056_s140_ble\ses
and
..\nRF5_SDK_17.0.2_d674dde\examples...
Hi,
I have been looking around the forum and have found conflicting information regarding the existence of a QSPI flash driver and example for the nRF53 on Zephyr. Is this...
Hi,
I am trying to run nrf zigbee light bulb sample provided in the nrf SDK on the NRF52850 usb dongle.
I have sucessfully built "blinky" app sample with NRF Connect SDK...
Hello Everyone,
I am developing one product for the HVAC system. I have Radiator and STM's primary MCU. For development, I need to configure the thermostat cluster ID for...
Dear Nordic Community,
Because of unavailability of nRF52840 we are shifting the work to nRF5340. I have some queries on this topic as follows,
1) Is SDK will be changed...
Hi Nordic Team,
I am new to Bluetooth mesh and NFC. I am working with the device nRF5340 and SDK NCS v1.5.0 .
I have used the sample Bluetooth: Mesh light as a starting...
Hello, I'm trying to use PN532 module with nRF52840 using I2C. the data can be sent, but when it comes to read it, IRQ keeps high, so it reads 808080 .. I added a nrf_delay_ms...
Hello,
Starting with the example of mqtt_sn_client_publisher in the nRF5 SDK for Thread and Zigbee and I want to publish an array of data like this one
in a MQTT topic...
I am trying to send some data from nRF52840 to Xbee via Zigbee In this case, I set nRF52840 as router and Xbee is the coordinator. I use zigbee_cli_agent_router sample code...
