I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I'm trying to get the SPI drivers working in slave mode. I have tested my master (Atmel L21) on an Arduino and I can see my message clearly. I'm trying to get nRF52833...
Hello
I want to access to the buffer to see what I am transmitting for then change the data to transmit to be able to verify, also I want to know where I can find de Kconfig...
Hi!
I have a custom board with a NRF52840 and some extra sensors for my application. I'm trying to comunicate with one SPI sensor but I have a little extrange behavior....
Hi,
I am trying to create a combined Bootloader + Bootloader Settings + Application hex file to flash the same into the devices during the production.
Bootloader Project...
i write 40bytes to flash 0x74000 and read 0x74000。i find it actually use 160bytes. I try to write a different number of bytes, it actually use 4*(write bytes)
this is...
I wonder if I can use spi1 or i2c1 on nrf9160. I use the 9160ns board configuration but non of my configs work for spi1 or i2c1 works. If I change it to i2c2 or others it...
I have a startup sequenced (nRF52832 peripheral) based on the s132 (v7.0.1 BLE 5.1) NFC Pairing example where it advertises at 1Msps link rate, then uses the PHY UPDATE API...
Hello!
We are working with NRF52840 dongles and want to be able to have them relay data over an OpenThread mesh network through UDP automatically. We have found within...
Hi,
calling "nrf_ringbuf_get()" immediately after "nrf_ringbuf_cpy_get()" returns an invalid pointer to the data. A workaround could be to assign "rd_idx" to "tmp_rd_idx...
Hi to all,
I have designed a custom board with 3rd party module (RAYTAC MDBT50Q) which includes NRF52840. During debugging on the custom board, two modules were demaged...
Hello,
I am using serial LTE modem for communication.
After trying to connect to TCP server using AT#XCONNECT I get following error:
The only official documentation...
In a system based on one nrf52-ble-app-uart-c-multilink-master and multiple ble_app_uart, the data from any entity is sent to all devices.
i.e. each ble_app_uart is sending...
Hello,
I'm using BLE peripheral device. I need to connect it to a BLE central device and exchange data. There are some connection procedure-
1. Discovered Bluetooth devices...
Hello, everyone, when I call err_code = fds_record_update(&record_desc, &record), I sometimes get an error: FDS_ERR_NO_SPACE_IN_FLASH.
Therefore, when this error occurs...
I have the nRF52 PCA10040 DK device, and I'm downloading the code from the online mbed tutorial. I'm using Putty serial port to communicate with the device at 9600 baud rate...
