the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Dear Members,
I create a loop inside main.c using code example ant_shared channel,
it's merged with ant_plus hrm_rx, but on forever loop, it stopped on 6 loops, it's...
Hello!
A frequent question in the forum is how to enable logging messages.
My question is exactly the opposite: I experience many NRF_LOG_INFO messages from Nordic library...
I'm having some issues with a design I'm developing using the ISP1807 bluetooth SOC (contains nRF52840). Every time I apply power to my device I have to manually reset the...
Dear Members,
How can I display multiple ANT channel ?
It looks like one channel is occupying all the resource (HRM)
How can I manage the time slice between channel...
Hi,
We are building our synthetic sensors using nRF52840 for smart buildings. In some areas we are using it with BLE only, other areas we use it with BLE mesh. When we want...
Hi,
Hope you are well.
I want to send the saadc data with ble to my pc. I used the below code. I am getting the data in the right format but i am loosing some data in...
I am experience some for me strange behavior with UART0 on a nrf52832. Let me explain:
First I initialize the UART using:
APP_UART_FIFO_INIT(...)
with parameters setup...
Hi,
I am using Ozone with nrf52840.
I used this example: wiki.segger.com/Tracing_on_Nordic_Semiconductor_nRF52840
I am able to debug fine. However, I am unable to see...
SDK 16.0 and SDK 17.0 (tried both versions)
nrf52832
Segger Embedded Studio
Windows 10
When Adding an additional ADC the sleep current increases to greater than...
I am currently using SWO to get tracing data from ITM and DWT successfully.
Now I want to use parallel trace for more throughput. For that I use an FPGA, no JTrace or similar...
I have NRF51822 softdevice, STM link v2 for flashing, segger embedded studio and nrf SDK. I have seen some videos on youtube on how to flash nrf softdevice using ST link....
Hi, all.
I'm using nRF52840 pca10056. s140.
I'm communicating with the CO sensor via uart, but there's a problem.
Sensor-side set to send rx steadily, and when debugging...
Hi, does Nordic provide the "works with all hubs" Zigbee cluster?
I see this blogpost mentioning " Watch out for more information on future Zigbee 3.1 SDK All Hubs support...
SDK: nRF5_SDK_for_Thread_and_Zigbee_v4.1.0
Board: nRF52840
Hi, I'm a newbie in zigbee stack. I have been get started with the door lock example.
I want to make custom...
