Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
Hi,
Using 'nrf5_SDK_for_Mesh_v5.0.0_src' exampe project 'light_switch' developed for nrf52 Development Kit(pca10040). How to make the same project working on Thingy52(pca20020...
I am working on a project based on the ble_app_hrs_rscs_relay example project which I have largely extended with many additional services.
For example I am offering an additional...
Hi
I am working on nRF52832 , I want to store the data in NVMC . so I am trying to write the data blockwise , I saw the layout each page consists of Block 0-7 .To each block...
Hi everyone,
Is it possible to implement a USB device belonging to the Personal Healthcare class with the nordic nrf52840 DK?
NRF supports Personal Healthcare USB class...
Hi, I have written these 3 functions to erase/read and write. When I write any value from address 1 it gives following wrong output(0 1 2 3). But When I start address from...
Hi nordic team，
I use the nrf52832 EVK ,I want to connect MIC and speaker to the EVK.
I read the nRF52832_PS_v1.4.pdf, and i guess following interfaces can be used.I don...
Hello
I am using Linux PC
nrf52832
chmod 777 to the nordic serial port
using the bt_nus_shell script :
sudo python bt_nus_shell.py --name BT_NUS_shell --com...
I want to use nrf5340 on DTM mode (installed through nrf connect) to test Carrier frequency offset for CTE packets using CMW500. However, CMW uses power trigger to find the...
I have developed a custom PCB based on nRF 9160. I have followed the connections as per the attached image
Can I use Segger Embeded Studio to program the custom PCBs. If...
Hi there!
How i can put nrf52840 NCP module into low power mode or turn it off? By SPINEL_PROP_MCU_POWER_STATE property of Spinel protocol getting error - "Prop_not_found...
Is it possible to implement a wakeup/power-on-long-push?
Working with the pwr_mgmt example from SDK 17, I see how bsp_wakeup_btn_config works to enable a BUTTON_ACTIVE_STATE...
Hi, I have a project in which I need to connect to an infusion pump via BLE.
I need your urgent help :)
The pump is advertising every 15 minutes for 10 seconds.
how...
hi,
Using nrf52840
setting new mac address results Error 12802:
using mac : 7F:37:DA:47:22:B1
gap_addr.addr_type = BLE_GAP_ADDR_TYPE_RANDOM_STATIC; gap_addr.addr_id_peer...
