The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi,
what is the valid range of interval for NRF_SO_GNSS_FIX_INTERVAL? when we set it to 5 it will failed, but 1 and 10 can be successful.
here is the code and error log...
I have a nrf24 transmitter and receiver that I want to set up for max speed. I have my SPI's both at max and I set the crf24 register to reflect 18db (was not sure how this...
Hi,
I am setting up nRF connect SDK into Mac, however I received an error below when setting up a project in SEGGER:
Could you please help me to remove this error...
Hi,
I am currently trying to understand the BLE mesh concepts, but its a quite tough process. At the moment I am wondering the following:
Let's say that I wand to...
HI
How stable is the serial_uartesexample in nRF5? I'm running it on a PCA10056, the example works for about 5 seconds and then UART RX stops, i.e. nothing is received after...
I see unexpected delays when running MQTT sample. The issue seems to be network related. When connecting delay is "normal" but after a few seconds roundtrip delay increases...
Hi everyone：
My case is to reveice some useful information form beacon device, but I have no ideal that is the softdevice s112 support observing so far ？
The s132 softdevice...
Hello guys,
We are working on the project and using DK 9160. We want to use LTE Cat M1 connection, mqtt tls and we need full functionality embed tls. We started with demo...
I am having trouble with the DFU/bootloader. I have built a board using the nRF52832 chip which I can program using SES using JLink connection, using SDK 16 and s132. I now...
Hello,
I am trying to figure out how the button presses in the module esb_low_power_ptx_pca10040 are creating events?
I have done some research and do not see this module...
Hi,
I have a problem when setting up pyaci on Windows 10 up to date.
In pyaci when launching the command
In [3]: p = Provisioner(device, db) In [4]: 2019-07-12 06...
I'm developing mesh nodes with serial interface, and have used the information in this thread to successfully modify the mesh firmware to support coded PHY
https://devzone...
Hello! We have an app with bootloader on SDK 15.3.0. Is there a way to jump from application into bootloader without setting byte 0 of GPREGRET register? I.e. without this...
Good afternoon,
First of all, I hope that you are all well and are able to work from home, regardless of the government instructions of your country of residence.
My question...
