Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
There is a period during which advertise packet cannot be received
Central info SDK: 15.3 nRF52840
Peripheral info SDK: 13.1 nRF52832
Running device Central * 2 Peripheral...
When I used light-switch server and client model simultaneously from
https://github.com/NordicPlayground/nrf52-mesh-light-switch-client-server-proxy/tree/master/examples...
Hi Nordic,
I have ported nRF_SDK_15.3.0 to nRF52840. These changes involves USBD. So While initializing pp_usb_init(), I see it is going to some hardfault handler. Please...
Description:
For my project I'm using 3 Nrf52840 DK, two of them as peripheral and the other as peripheral and central. I'm using also an iOS device as central. The two...
Hello,
I bought a Adafruit Feather M0 Bluefruit LE, the Bluefruit LE module is an nRF51822 chipset from Nordic. I connected the Adafruit board to an accelerometer. This...
Hello, i currently evalutate LTE-M for my company and i run into a lot of trouble for starting the test. But at least i have able to do the test
I have cut a lot of code...
Hi Nordic,
It reads in devzone.nordicsemi.com/.../38040
"According to Section 8.23 in the Product Specification a logical high is between 0.7*VDD and VDD and a logical...
Although BUTTONS_ACTIVE_STATE declared as 1, the hal_buttons_init(button_event_handler) yields an event when the input sees a high to low transition in stead of a low to high...
In testing the timers on the dongle, I have made a GPIO pin be controlled by the timer triggering.
So the following has a constant time between edges:
case NRF_TIMER_EVENT_COMPARE1...
I ran into the same problem as other user one year ago (I was using Arduino Studio nad Segger Studio before), now I switched to IAR (as recommended) and as the examples are...
Using SEGGER Embedded Studio for ARM v4.20a (64-bit).
I'd like to add a new source file to a nRF9160 sample project. The menu selection Project --> Add New File is grayed...
Hi,
I had a custom nRF52832 board. I did some modifications on it. But the same code doesn't run on modified one.
Just to check, Debugging on Segger the yellow arrow(i...
I've been following the guide linked here and got to the point where PCA10090 is flashed with Hello World project. However, when executing "west flash" command, an error appears...
Developing on a custom nRF52832 board, not the Nordic nRF52 dev board, but continue to use version 15.2 of the SDK. Building and download application, but get an abort before...
