Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
I am using mbn52832 BLE+MCU module and i am facing issue in one of the GPIO pins.
I am facing issue in P0_29 pin and i am driving the P-channel MOSFET from this pin. I have...
Hi,
I would like to configure the watchdog timer for the nRF9160. I have attempted to run the Zephyr example application (path/to/zephyr/test/driver/watchdog/wdt_basic_api...
Hi:
i am working with Thingy52，and i have get a zip pack named thingysdkv210,today after the compile prcess after following ../PCA20020/thingysdkv210/documentation/firmware_compile...
My problem:
I have to setup a BLE connection between two nRF52 devices one central device and one peripheral device. I have multiple central devices (C1, C2 to Cn) and multiple...
We are developing BLE 5.0 products using the nRF52832 running the Nordic S132 v6.0.0 softdevice and SDK version 15.0.0.
We noticed that one of our test devices, a Huawei...
Dear all,
I am trying to develop an application that reads data from a sensor (accelerometer) and I want to be able to update the advertisement packet with the measurement...
Hi, I am using nRF52832. I want to update my boot loader using DFU, I am unable to find correct command to get .zip file. I am using below command:
nrfutil.exe pkg generate...
Hi,
For my home Mesh network, I use a Android mobile phone + nRF Mesh App as a mesh provisioner to configure the nodes, and control the mesh node as well.
There're about...
Hello，
When I use the nRF9160 to upload the data to the cloud based on the LTE-CatM1, what's the maximum current? The datasheet of nRF9160 mentioned:
1. Application CPU...
Hi all,
I'm struggling with UARTE and easyDMA. i just want to send data with TX.
I am trying to configure it with the hal librairy but i cannot manage to make it work...
Hi I would like to, at app level, implement access control to characteristic. My characteristic is configured solely as notify (no read, no writing).
When a smartphone turns...
I am testing about tx power level on nRF5_SDK_15.3.0_59ac345 with nRF52840.
I have some confusing about sd_ble_gap_tx_power_set() function.
In peripheral advertising...
Hey guys I want to resolve some issues regarding RSSI values received from BLE beacons. I have ibeacons type.
1: Ibeacon format says the last byte is signal signal, is it...
Hi, after following the tutorial about building the asset tracker firmware I came to the problem of generating merge.hex file. The zephir.hex file is generated, but the merge...
chip: nrf52840 aQFN package
5~10% of the products were defective. by causing analysis, There are short some pins bottom of chip.
I already read this guide after this...
