I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hello,
I tried to build the mesh sdk in all way.
Please help me or send me the sdk set-up which is without error.
I tried by sdk15.3.0, sdk15.2.0 and mesh sdk. Try...
Hi,
I am having problems with using BLE along with gpiote and ppi for measuring the delay between two waveforms and sending the delay between them to an app using bluetooth...
Hello,
I have recently built and flashed CoAP Sample on my board.
After that the device cannot connect to the mobile network.
Could you please provide me a description...
Hello,
We have finished the development of a prototype device that incorperates the nRF9160 SiP. I would like to know if there is anything I need to set-up in the device...
Hi,
I would like to use hal_time_get() [hal_timer.h] in my project, and I try to add below library into Makefile.
but I got an error. "error: implicit declaration of function...
i am using/ ble_app_multilink/ example present in central folder..i am beginner to this ,,so i have few doubts in it
1)so where actually advertisers(which are advertising...
Hi,I had a problem with nRF51822 DFU.I tried to OTD nRF51822( version SDK_9.0.0 s110 ) wiht Android 9.0 devices( nRF tool version 1.9.0 ),but it always fail at 1%.The problem...
Hello fellow Nordic-ians,
I am developing a custom firmware for Nordic Thingy 52. I am using the Segger Embedded Studio as my IDE and J-link Edu Mini as the programmer ...
Hi,
I have found zboss 1.0 opensource.
Surveying the source, i have noticed that variable "g_zb" (nicknamed by ZG) give system informations.
I can find zed address(16bit...
Hi,
Here is my setup, NRF52832 PCA10040 s132, sdk 13.0.0.
I work on Windows 10 with a server (The aim is to do it from a Raspberry later) which one is connected to my...
Hi,
I'm developing a simple sensor application using s132 on NRF52832_XXAA. The application works fine, except that I have problems disabling the saadc module after conversion...
Hi, How can I configure so that I can transmit real GPS data of the device and watch it from nrfcloud? I think I need to change something in config files? Simulated GPS data...
Hello,
in the ble_advertising_start() function of SDK15 I noticed, that the check for the secondary_phy is the same as for the primary_phy.
I assume this is a copy paste...
Hi.
I am trying to choose the crystal and external capacitor for nRF51822-QFAA-LDO. I found the crystal with load capacitance 10pF. As mentioned in reference paper,
...
Hello. I am having problems when I connect one of my PCA10056 boards (nRF52840-DK) to my Windows machine and run nRF Connect v3.0, Bluetooth LE app v2.3.0. When I select the...
