Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Using the scanner module, I set up a scan filter to scan for UUID with no auto connect. In the scan_evt_handler, I have a switch case for the NRF_BLE_SCAN_EVT_FILTER_MATCH...
I want to secure advertised packets using ccm
I am using s132 , SDK 14.2.0 and nrf52 dk
I found that AES-CCM peripheral is blocked by soft device usage and that I need...
I have this error.
In a last time with same error on a nRF52832 I decided this problem with increase:
On the 52832 it works. But on the 52810- project fall.
How to...
Hello,
I am using nRF52832 DK PCA10040 v1.2.4, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
As part of ble_evt_handler...
Hello All,
I am developing a custom board with nRF52832. All good with Segger Embedded Studio, I could download and debug the board successfully.
When I tryed to program...
Hi, i'm using nRF52840
I'm using 2 uarts :
one (uart0) is only for logging and another one (uart1) is for communication.
I can send from both uart, i can see i receive...
Hi
I sometimes get stuck in the zb_nrf52840_abort but the stack trace seams to be strange, its only containing two levels, Am I missing something or is there a better way...
Hello,
I have inherited a Thingy:52 project which was using some old versions of SDKs. Now I am trying to port it to a newer version in order to make it compatible with...
In nRF5_SDK_15.3.0 some undefined reference error reported when using nrf_drv_clock module (example: undefined reference to `nrf_drv_clock_hfclk_release)
The problem is...
Hi,
Is it possible to update the modem firmware once the product is on the field? I'm not talking about the application hosted on the M33, but the actual modem firmware...
Hi,
I'm testing pca10059 usb dongle with pc-ble-driver (not nrf-connect-pc)
I need 2M phy because of throughput.
latest pc-ble-driver support nrf52840 with softdevice...
HI,
i'm using SDK 15.2.0 and MESH SDK 3.1.0.
my program using the uart to get data from a sensor and sending it over the mesh network.
now i'm trying to write to the...
Hi.
I'm using
An nRF52832 DK
SDK 15.3.0
Segger IDE
The soft device is S112
JLinkRTTViewer for debug
I'm using the ble_app_proximity as my starting point and...
Hi Nordic;
I am using ble_app_uart_c example to scan data with BLE_GAP_EVT_ADV_REPORT. So now i have to send this information to Arduino Uno how it would be possible?
...
