Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello there!
I'm developing an nrf52810-based device, which needs to be as small and simple as possible, pretty much like your nRF51822 Beacon Kit.
I've founded the nrf52...
I successfully tried the "beaconing" example from your Mesh SDK 310.
I noticed that moving
line 215 "adv_start();" in main.c
right after "ERROR_CHECK(mesh_stack_start...
Hi, I am using nRF5 SDK for Thread and Zigbee v3.0.0, and I want use NFC pin and RESET pin as inputs.
I wrote in my .emProject this preprocessor definition "CONFIG_NFCT_PINS_AS_GPIOS...
Dear All,
I know that the max. input on VDD is 3.6V. But as a rule of thumb, I normally try to stay below the max. rating. But this time I have a peripheral LDO with 3.6V...
Sorry： Use google translation
I am compiling sdk using keil 5.27，use compiler version 6, armclang,
but is error:
Undefined symbol __start_pwr_mgmt_data...
I know...
Hello,
I am trying to create a new project after add source files and header files . While compiling I got error like "device must be defined. see nrf.h.segger"
Kindly...
Hi,
I'm asking this becase it is not very clear about the PWM in Product Specification v1.6 for nRF24LE1 in the nRF24LE1_PS_v1.6.pdf mentioned the pwm Frequency-range from...
I am using nRF5_SDK_15.2.0_9412b96.And we have code written to interface ads1298r to nrf52 dk for acquiring ecg signal.But the strange is the code is compiling in all others...
Hi guys,
Do you have any suggestions on how I can lower the power consumption. I am currently connecting - sending data - disconnecting .
I have the following set the...
Hi,
I'm trying to receive large packets on uart, but is seems to read one byte at a time .
uart_fifo_read() always returns 1
why is that?
can it be changed ?
Hey guys, i recently bought a nrf52 DK to implement a gateway between a usb touch monitor to a device such as a android or a computer.my approach is recovering the hid raw...
I'm using the nrfx drivers of SDK 15.3.0 and want to poll for data using a synchronous UART. In order to check for data, I use the 'nrfx_uarte_rx_ready' function. However...
Hi,
The documentation seems scant and IDE behaving inconsistently with regards to how basic project management, adding source files, libraries etc to a NRF9160 project,...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flash the image.
I started development on top of ‘ble_app_blinky’ code.
I have few queries...
I have a strange problem. I have two nRF52840 DK boards and I build an application on top of the light switch example. One board works fine, but on the other board stuck in...
