I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hi all,
I'm working on a project which will automatically send data from LM75 sensor through mesh proxy_client to proxy_server. So, I did merge two examples twi_sensor and...
Hello Nordic team
I am working on ble_app_buttonless_dfu example code and implemented accelerometer code via TWI0. And Accelerometer INT pin connected on GPIO via gpiote...
I am looking to develop a number of Zigbee compatible devices for home automation. Can you tell me if the nRF52840DK and dongle (no debugging using the dongle I understand...
Hi all,
After I combile light switch example and remote example for my client and server board . Function Remote run fine . But when I push button for send unicast message...
Hi. I try to run example Light Switch Demo.
I use: Mesh SDK v.2.2.0. NRF SDK v 15.0.0. Softdevice: s132_nrf52_6.0.0.
I see that relayed messages have maximum TTL = 4,...
Hi, I already have device that plays audio from sd card. New feature is needed that user can send MP3 file to device from mobile phone that will be stored in sd card and then...
below is a little part of code copied from nrf5_SDK_for_Mesh_v2.2.0_src:
***********************************************************************************************...
Hi team,
I am integrating bmp180 and mpu6050 into a beacon code.While integrating,I am getting the following error
"NRF_ERROR_MODULE_ALREADY_INITIALIZED".
Please help...
SDK14.2
Segger Embedded Studio
nRF52 development board
According to this post https://devzone.nordicsemi.com/f/nordic-q-a/20556/how-does-the-saadc-scan-mode-use-the...
Hi All,
Currently i am working on Zephyr RTOS as a target of PCA10040 DK.I have been compiling and executing a simple "Hello World " example.
While doing cross compilation...
Hello,
I have use the BLE Multi-link Example as a central. For the priripheral I have use BLE Blinky Application and UART/Serial Port Emulation over BLE ( <InstallFolder...
Examples in SDK15 use the Observer pattern to handle BLE events (using the macro NRF_SDH_BLE_OBSERVER). AFAIK, the registered handler runs in some IRQ context, typically higher...
Hello Nordic team
I am working on nRF52832 DK, SDKv15.2.
My question is how we can send and receive more than 100 bytes of data? I know nus services doing it. Also how...
Hello,
On one of our custom board with nrf52832, after programming it like 3-4 times it stopped responding on the nrfgostudio as in it was showing no device detected,...