Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Hello,
For BLE mesh light_switch example, the following statement is showing error.
In app_config.h
#define NRF_SDH_ENABLED 0
In sdk_config.h
#ifndef NRF_SDH_ENABLED...
Can someone tell me how to make device go to sleep and make it wakeup after a few hous using systick timer. I know how to create a timer but i wanna know which system call...
Hello. I have a breakout board (SMARTMP3 VS1053) and it has also a slot for memory card, so I connect the wires (SCK, MOSI, MISO and CS) to my nrf52832, but it can't see the...
What is the recommended way to protect characteristic value from modification while it is being read by a client?
I have a test application with 500-byte long characteristic...
Dear Team,
is there a tutorial on how to start from scratch a project for zephyr nrf91? With all configurations and flags...
That would be great!
Thanks & cheer
O...
Hello,
We're trying to create a custom bootloader from scratch and we're struggling with a weird behavior. This is for the nRF52840 and the bootloader doesn't use the softdevice...
The SDK version is 15.0.0, SD 132, single peripheral conection.
the configuration:
this is how i request the timeouts:
With the timeouts of about 50ms and less, the...
Hi guys,
I tried to modify "configs.c" or ".config", modified CONFIG_GPS_SIM_TRIGGER_TIMER_MSEC = from 2000 to 10000 .
But the device still sends GPS data every 2 seconds...
Hi there
I have a design in production using Gazell at 250kbs on a NRF51822
I would like to update the design using a nRF52840 but it doesn't support the data rate that...
Hi,
We are looking for a consultant to help us port our product's ( https://www.ncase.io ) firmware from Simblee to the Nordic nRF51822 or nRF52832. Experience with Nordic...
Dears:
I test the uart dfu by examples\dfu\secure_bootloader\pca10056_uart
After I enter command like below：
nrfutil dfu serial -pkg Sena_app_uart_s140.zip -p COM5 ...
My project is Obj-C , and “ pod 'iOSDFULibrary' ” in my Podfile.
It worked fine until I upgraded Xcode to 10.2. There are some errors(about 100) occurred during project...
Hi all
I am doing multiprotocal from sdk15.3 and I am trying to add nrf_gzp.c, nrf_gzp_host.c, and nrf_gzp_host_nrf5x.c in to the project
after compile successfully and...
I was wondering, is it possible to suspend/resume flash operation in nRF52840 (internal flash)? Like flash erase suspend, and also flash write suspend/resume?
Thank you...
Hi,
Might be a silly question,
but is there a gattc equivalent of the "BLE_GATTS_EVT_HVN_TX_COMPLETE", ie a similar/equivalent event that gets generated when a central...
