I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
A general question about the radio CRC registers: The CRCPOLY register is 24 bits wide, which can be used to specify a 24-bit polynomial, suitable for calculation a 23 bit...
Hello Everyone,
I need to turn off the bluetooth advertising on certain event/interrupt and start advertising again on another event/interrupt.
I have gone through the...
Have a nice day! We are working on a project where goal is to build up mesh-network up to 50 nodes with high sum data rate to up 100kbps through the node. For this purposes...
Is there any release timeline for a Nordic Thingy based on the nRF52840? Does anybody know of an open-access beacon that incorporates the nRF52840? Thank you.
I'm trying to communicate with a single NeoPixel ( WS2812B) using the PWM module.
I've configured a sequence array with the compare values necessary to turn on the red and...
Hi everyone
I'm trying to get the status of button by using the bsp_event_callback_t, but my application crashes when I push on any button.
Test environment: Freertos...
Hi Team,
For the board having Linux Host having nRF52832 interfaced over UART, what are the maximum number of BLE devices can be connected?
As per my understanding it...
Hello, this is Kwonjoon Lee, beginner of BLE development.
I successfully installed pc-ble-driver (c/c++) in accordance with Git-Hub guide ( https://github.com/NordicSemiconductor...
Hello,
This is Jahnavi. I am having nrf52 DK development kit and with that development kits I am using light switch example to connect the boards as mesh network. How...
Hallo everyone,
I'm using Eclipse IDE for C/C++ Version 2018-12 (4.10.0), my OS is Ubuntu 18.04.2 LTS and my hardware is the NRF52840 DK. I'm using the GCC C and C++ Compiler...
Hello:
I have nRF9160 SIP custom board. The pins on custom board almost the same as nRF9160DK.
I can run lte_ble_gateway sample on nRF9160DK without problem:
But...
I followed nRF Connect SDK 0.3.99 to test nRF9160 LTE Sensor Gateway.
I successfully completed steps 1 thru 10 in the Testing section
It was successfully connected...
Hi all,
I am communicating with a sensor through UART using APP_UART on a custom board (nrf52840) through the nrf52 DK. I can send and receive commands to and from the sensor...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
We are using nRF52840 with BLE and 802.15.4 concurrent with S140 SoftDevice. There are two functions to set the transmit power for each radio protocol:
sd_ble_gap_tx_power_set...
