nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I am trying to compare a bunch of BLE mesh options and I am trying to evaluate the software stack for nRF mesh
Whilst trying out the light switch proxy example, I noticed...
Hi Great Nordic Team:
I have some questions about nrf24ap2 reference schematic, please kindly help to give me some tips.
※it's reference circuit of Synchronous (bit...
Hi Sir,
As reference below link, and we can find the Tickless IDLE enabled ~700uA in SDK 15.2
https://devzone.nordicsemi.com/f/nordic-q-a/24733/nrf52840-sdk-14-0-0-and...
Hi again!
I'm trying to send/receive data between an nRF51(master) and a AVR/HM-11(serial/BLE module)(peripheral)
After following this visualgdb.com/.../ tutorial based...
Under some conditions I want to force advertising to transition from slow to fast. With SDK 14, I could just call ble_advertising_start(&m_advertising, BLE_ADV_MODE_FAST)...
Earlier for nrf52 we could filter out connections on the peripheral based on rssi, need similar operation for nRF5_SDK_15.2.0_9412b96\examples\ble_peripheral\ble_app_uart...
Dear Nordic,
I have one nrf52840 dongle.I want to know which polarization of antenna (PCB antenna) gets maximum range?
another thing i want to know what is the maximum...
Hello,
I want to know if there are some SDK, application note or similar about how connect point to point a nRF52 IC to Alexa and Google Home.
Thanks in advance.
Jose...
Hello,
Greetings from India!
I would like to have my design review by your engineers or any concerned person in the related field. The design is not yet complete but the...
I'm using three nrf52840-dk's, from an ubuntu 16.04 x64 host.
JLink v6.30b
nrfjprog v9.7.2
I can program and interact with two boards fine, with zero of the failures...
hello all ,
controller nrf51822
i am trying to development for EPD 7.5 spi interfacing through external flash image send .
my question is i am using reference code for...
Hi, everyone,
We are developing BLE project on nRF52832 chip by using SDK14.0 software.
The project is build from one master-device and many slave- devices.
The master...
hi............
i want to modify the ble hts program , inorder to add a timer in it. i want to transfer the data for every one minute ,so data have to read for every one...
Hi.....
i want to transfer the data for every one minute from peripheral device to phone (nrf connect ).. how to declare in the program and what function to be used ?
...
