Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
Hello,
I am working with nRF51422 & would like to know if I can measure current of single event & multiple events (pictures attached) as detailed as possible. I have cut...
Hello everyone.
I want to increase the operating range for nRF51822. To do this I added PA SE2576L in design.
Unfortunately, I do not have experience in RF develop...
Hi,
I'm attempting to use Version 2.1.0 of the HomeKit SDK on an nRF52. We're using the s132 SoftDevice 2.0.0-7.alpha (the SoftDevice in the latest nRF5 SDK v11.0.0). ...
Hi.
So my problem is, that i cannot successfully program external board with preprogrammed nrf51822 chip in the board.. This board is from china.. its an ibeacon.. If i...
I've recently been playing around with Bluetooth Developer Studio, and I can see it's potential despite it having a few annoying bugs.
I've set up a custom service by re...
Where would be a good place to feed a watchdog when using a softdevice?
My first guess was in main loop:
for (;;) {
NRF_WDT->RR[RR_number] = 0x6E524635;
power_manage...
Hi,
When a watch dog timeout occurs, I want to save some data to the flash memory prior to reset (namely the RTC count value). Therefore I enabled the wdt interrupt. The...
Im using nrf51, I configured the watchdog to reset after 3 seconds of hang and it works. But I have absolutely to save some data in flash before reset
Is there anyway to...
My custom profile was being built fine until I added a couple of standard descriptors to a custom service characteristic. Any idea what's going on here?
19:34 - [Code Generator...
Hello All,
I want to develop bluetooth mesh using NRF51.
I have question about this:
Is their library closed or not?
Do we need smartphone like in CSR?
...
Hi, I have a TinyShield Nordic module and I am having some troubles trying to customize the advertising packet. I have downloaded NRFGO Studio and I have enabled service data...
I have an nRF 52 dev kit, an Asus router running openWRT, and an android phone with the master control panel.
I'm able to compile and flash the dev kit with the example...
hello,
I am using the nrf51822, I want to add a normal service which do not need bond before used at the ancs example.I hope it can do the follow tow points,firstly,if the...
Hi,
I tried to figure out what is happening on the lower Bluetooth levels but it is very difficult to find straightforward information. Especially the Bluetooth (4.2) standard...
Hi, My apologies that this seems repeat information from previous posts, however they do not give a clear answer to my question regarding 4.2 compliance. I must also state...
