The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi!
I have bought the nrf51822 EV KIT and it came with 5 extra nrf51822 modules but them without a board. I have researched a little and I found that I need the Segger...
Hi,
We're using an off the shelf module with a trace antenna that can't be modified.
Measured the module once assembled, and due to surrounding plastic materials, the...
Just finished upgrading to the latest SDK Version -- and trying to build some of the examples -- but consistently getting compilation errors when building any of the nRF51822...
When working with BLE, one sees a lot of different names for roles, which is confusing. What is actually the difference between them all, master, slave, central, peripheral...
Hello to everyone,
I'm developing a new project with a nrf8002 and a Smartphone with Android 4.4.2. Both devices connect to each other fine, and I can bond them with no...
Hi,
I made a peripheral firmware based on "s110\experimental\ble_app_uart" example, but I don't know how to write a central module FW so that these two can pair to each...
The reset handler as shown in the C:\Keil_v5\ARM\Device\Nordic\nrf51822\Source\templates\arm\arm_startup_nrf51.s will call SystemInit as defined in the C:\Keil_v5\ARM\Device...
Hi
im unable to connect nrf51822 EK with nrfgo studio
how can i solve this issue
m using all latest version softwares
and wen i click ok it shows as below
...
Hello, i know its an often discussed topic but i already read lots of threads about it and didnt find the answer.
I have a simple program that enables the softdevice s110...
Hi,
We are using an nRF8001 with bonding.
We tested the use case were a bond has been established with an iOS app. Then the connection was terminated by closing the...
Hi
am using a thermistor of 10 k with a known resistor of 10 k ,and am giving the voltage divided input to ANI2 (p0.02).The suppply voltage for thermistor is external of...
Hi,
We designed an nrf51822 BLE application using the mbed kit and on-line tools.
Our target pcb has a 1.8V onboard supply. To minimise consumption i want to disable the...
I have an android client that functions as a central and have an app on my MAC (peripheral) that this central connects to and sends data.
At this point, I need to wait...
hi.
we are planning to use 3 chips of 51822 to implement a data collecting system. one chip uses s120 and the other two use s110. chips using s110 collect data and deliver...
Hi,
I have a piezo buzzer connected to pin 14 on a Nordic nRF51822. Here's some code I use to drive it, based on the Nordic PWM library here: github.com/.../nrf51-pwm-library...
