hi support team,
customer is testing our nrf93M1 module, and find out, when device enters system mode after sleep, there will be a lot of URL sending to UART as below: ...
I tried to switch to OAT. Now I use new API
" api.nrfcloud.com/.../ long-range/devices/bulk" with OAT bearer token for devices creation
instead of old API: " ">api.nrfcloud...
Hi Team,
Please help to assist below customer concern regarding MPN :NRF54L15-CAAA-R7
They are looking for China typically require a valid Radio Transmission Equipment...
We are currently using an NRF54L15 with TF-M on NCS 3.4.2. We have a custom secure partition, and want it to own a persistent P-256 ECDH private key and derived AES-128 key...
When I connect the two-pin battery and short pin1 and pin2 of P1, I am unable to get the battery voltage at J1 AND WHEN I LEAVE THE PINS UNSHORTED FOR P1, THEN I AM NOT GETTING...
I have connected the correct 47K res for VSET1 but I am not getting 1.8V, instead I am getting 2.3V I am getting the correct output for BUCK2 as 3.3V I have checked the resistor...
Hello, We have one of our products developed using the nrf52805 Module & nrf5 SDK . (which is already fully functional with our application ) Since we have few production...
Board : Nrf52480 custom board
IDE: VSCODE
NRF version : 2.6.99
Zephyr Version : 1.6.0
Segger systemview: 3.54
I followed the instruction from Zephyr RTOS, for using...
Hi support Team,
I would like to know the SDK version to be used for nRF54L15.
Is there any link to know details regarding the configuration, flashing and example codes...
I want to advertise a custom service so my central can filter for it and have a device name and manufacturer. I have the following code but can only seem to do either the...
Hi all,
I want for confirm my findings concerning ERASEUICR. I want to be able to erase the UICR from inside my firmware for automatic testing purposes (no debugger is...
I think I have a failing PPK2.
I tested it with this circuit.
My DVM shows the correct current flow - 1.48 mA. The PPK2 shows 40 micro Amps.
Note that the battery...
Hello,
Using nrf9131-ek because the nrf9161 doesn't seems to have the capability of using an external RC oscillator.
Plans are there in the project with using some/many...
Hello,
Using nrf9131-ek because the nrf9161 doesn't seems to have the capability of using an external RC oscillator.
Plans are there in the project with using some/many...
i have used this case:devzone.nordicsemi.com/.../using-swo-with-nrf52-redux and add ENABLE_SWO but when i flash and use jlink swo viewer,it will have this problem.
...
Hello DevZone!
I am using a nrf5340 with the nrf Connect SDK v2.6.0. I have been running into an issue that has come up a few times on separate occasions. Basically, for...
Hi,
i develop my product ny ncs V2.6.0. when i view the code
I noticed the annotation, it says “Edge interrupt gives only 7 channels. It is not suitable for larger matrix...
Hi. I have some question regarding to Bluetooth 5.4 on Nordic platform
1. Can Nordic platform do Advertising Coding Selection? I saw some old old issue that the device...
Hi,
I have tried to update the nRF Connect for Desktop app (v.4.2.0 to v.5.0.2). Unfortunately, the process does not work through the end. Once the installation of the new...
I have to use 240 bytes for my sensor value to send in bluetooth. so i choosed to work on ble_app_att_mtu_throughput i need only pheripheral to work on it . i have to remove...
