Hello,
I have 2 Memfault projects that I'd like to rename, but I can't find any way to do this through the web app, and the API authorization keeps getting rejected (tried...
Hello, I'm working on a prototype device based on the nRF9151 DK.
HW: nRF9151 DK, nRF9151 LACA A1A Tested with modem_shell sample app, NCS v3.4.0.
Symptom: on boot, "The...
Hi, I have a question with regard to the nPM1100 PMIC and entering ship mode (not exiting it).
If I am interpreting the datasheet correctly, the SHPHLD pin must be held...
Hi Nordic Support,
I am facing an issue where the peripheral registers are not visible in the Keil debugger during a debug session. Only the core registers are available...
Hi:
Use nRF54LM20A_DK.
Use ncs 3.1.1.
And this is source code:
The following error occurred:
« *** Booting nRF Connect SDK v3.1.1-e2a97fe2578a *** *** Using Zephyr...
Hello, I use the NCS v3.3.0 (ncs\v3.3.0\nrf\applications\nrf_desktop). Can the desktop dongle connect to two keyboards at the same time? Development boards: two nrf54lm20...
With SDK 3.3.1 I do not get the <inf> logging messages when building the Hello World app unless CONFIG_LOG=y is added to prj.conf.
Perhaps this is left as an exercise for...
Hi,
I am working with the ESB (Enhanced Shockburst) library using the nRF Connect SDK 2.6.1. The library seems easy to use and has the main things that I need.
However...
Hi
We are currently in the midst of our production process and are utilizing a microcontroller that communicates with a BLE chip. As part of our quality assurance, we aim...
I want to use XY485 converter for serial communication between 485 relay and nrf52832. The converter does not need enable as it does it on its own. I have implemented this...
Hallo everyone,
nrf52840 Dk (Master device)
MAX86140 (Slave device)
I have been working with an AFE (Analog front end) sensor recently. It is a 19 bit charge ADC with...
Hi there,
I have some nRF5340 Audio DKs, and have got the example nRF5340_audio application working fine. I am using VS Code on Windows for this, and SDK 2.4.0.
What...
I am trying to run the NCP light_zc sample (with nrf52840 dk on usb) on latest RaspberryPI 4 (aarch64)
The sample starts, does some communication on usb then the nrf reboots...
Hi,
I am trying to use the UART on my nRF9160DK board.
In my program I have 2 uarts in use. uart0 is used for printk output and uart1 is used to receive data in async...
Hello! I'm working on an application with precise timing and I'm using timers and PPI.
In the callback pulse_end_cb() I seem to get garbage instead of the parameters, which...
Hey, so we have been building a prototype similar to a hearing aid with the nRF5340 Audio DK. I had a few queries regarding the DSP block of CS47L63 Hardware Codec which is...
Hi,
I'm implementing a BLE GATT peripheral that has no display but it does have a button.
I'd like to make some characteristics only available to devices that are BONDED...
Hi,
I am using CJSON_LIB from nrf-sdk modules, I even tested this cjson lib in such a simple way in helloworld app (I attached the sample project.), and after running for...
Hi!
We're looking into possibility to use nRF5340 and nRF7002 to provide BLE and WiFi access to an external MCU. The idea is to use one of NXP's MCUs as the main processor...
In the Power Profiler, when I select a larger area in the data logger, then it stops updating the selection time. It works great till 16:40m, but then stays at this value...
Hi,
We have developed our code against SDK 2.3.0 and I wanted to try to upgrade the SDK to 2.6.0. I had to remove CONFIG_OPENTHREAD_CHILD_SUPERVISION from my prj.conf, but...
HI
I basically define uart_init(); in Main.
And use DEBUG below to decide whether to use UART.
#ifndef DEBUG
NRF_UART0->TASKS_STOPRX= 1; NRF_UART0->ENABLE =...
