We are migrating following your November 11 notice. Two read-only Identity Service operations remain unresolved:
- POST api.identity.nrfcloud.com/.../verify-jwt authenticates...
hi support team,
customer is testing our nrf93M1 module, and find out, when device enters system mode after sleep, there will be a lot of URL sending to UART as below: ...
We are currently using an NRF54L15 with TF-M on NCS 3.4.2. We have a custom secure partition, and want it to own a persistent P-256 ECDH private key and derived AES-128 key...
I have connected the correct 47K res for VSET1 but I am not getting 1.8V, instead I am getting 2.3V I am getting the correct output for BUCK2 as 3.3V I have checked the resistor...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Dear Team,
I have been running two nRF54LM20-DK as Initiator and Reflector for Bluetooth Channel Sounding.
I adjusted the ranging algorithm RAS_Initiator to print Local...
Hi,
I'm trying to find out how people automate current measurements with the PPK2 beyond doing it by hand in the Power Profiler app.
From the threads here it looks like...
Hello,
I want to add an extra button on nrf5340 Audio DK.
I use P1.14 as the pin of this new button and set it in the overlay file.
The default buttons use DT_GPIO_PIN...
I am using nRF9160: nRF CoAP Client and Thread: CoAP Server Thread: CoAP Server samples on a network. I can transfer built-in Unicast and Multicast messages, but I couldn...
I am currently working on nrf52840 android app(Java). I want to provision all nodes at once becuase it takes much time to provision node one by one. please help if there is...
I have used Partition Manager to insert a non-secure static partition at the start of Flash.
The problem is that reading addresses within this partition using the zephyr...
Dear Nrodic Team,
I am connecting LEDs to nrf9160dk which is pin 14 and pin 15. In the following code, I have configured such that LED0 is aliased to Pin 14 and LED2 is...
Hello,
I am using the nRF9160 on a custom board as the main MCU and an ESP32 as Wifi/BLE MCU.
On the ESP32 I am using the esp-at firmware to expose AT commands to configure...
I have an application modified from the Asset Tracker V2. It is on the 1.8 SDK.
I am able to get the power consumption low, but every 20 minutes the application starts the...
Hi,
we are planning to use nrf9160 with LET in INDIA but i have query Is nRF9160 support's LTE network in INDIA
https://www.nordicsemi.com/Products/Low-power-cellular...
* nrf5340 - nrf connect 2.0.2
The BLE name of our company's product starts with ABC as below and is followed by a number. (ABC-0000001 ~ ABC-9999999) The product we need...
Hi friend,
I am using SDK16.0, and the version of softdevice is S140 V7.0.1. Can I set nRF52840's TXPOWER register to 1 i f I want to set BLE TX power to 1 dbm? Can I s...
I have a custom board based on the nRF52810. I have LEDs wired to GPIOs 12 and 13. I want to modify the blinky example to use the custom board.
I used the "Create new board...
I'm looking to use a debugger with nRF Connect. So I'm starting with a build of the hello_world test for my nRF52 DK. I checked the box to "Enable debug options" and then...
I may be misunderstanding my issue but, in essence, I believe I'm experiencing the same thing as the poster here:
However, in my case I'm reluctant to introduce a pm_static...
Our system is working fine defining the default APN in the prj.conf file. We are using the LTE Link Controller.
What I need to do is set the APN based on the SIM that happens...
