Hi,
We are using nrf54l15 soc in our product and using NCS SDK 3.4.0. The LFCLK is set to SYNTH mode where it derives the clock from HFCLK. We have a crystal driving the...
NCS 3.0.1
nrf52840
nrf21540
I have read several tickets regarding antenna diversity and BLE. It does not seem to be supported for BLE. What about Thread?
I have read...
Affected: nRF Connect SDK v3.4.0; the same code is on main as checked on 2026-11-11 ( subsys/net/lib/nrf_cloud/common/src/nrf_cloud_codec_internal.c , subsys/net/lib/nrf_cloud...
We are currently using an NRF54L15 with TF-M on NCS 3.4.2. We have a custom secure partition, and want it to own a persistent P-256 ECDH private key and derived AES-128 key...
When I connect the two-pin battery and short pin1 and pin2 of P1, I am unable to get the battery voltage at J1 AND WHEN I LEAVE THE PINS UNSHORTED FOR P1, THEN I AM NOT GETTING...
I have connected the correct 47K res for VSET1 but I am not getting 1.8V, instead I am getting 2.3V I am getting the correct output for BUCK2 as 3.3V I have checked the resistor...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Hello All,
I am referring to the ble_app_interactive example and it works fine. I wrote similar functions in my project to scan nearby BLE and connect BLE if it's RSSI goes...
Based on online simulation
//devzone.nordicsemi.com/power/w/opp/3/online-power-profiler-for-lte
The settings is different for the case of 30 mins when comparing settings...
Please clarify the following in LTE PSM mode. Especially TAU is based on time vs frequency is 1/Time. What is frequency second ?? Is it frequency or it is seconds in time...
I've got an nRF52832 DK board. When I connect it to the USB bus, I see the following in the nRF Connect app:
I can run the hello_world app and see it output "Hello World...
I have a nRF52805 system with an external timer to reset it from system_off power. I need to initialize, then keep some user settable values thru the post powerup resets....
Hello!
I have been developing with the nRF52833, and have built a custom PCB to interface with an on board nRF52833 SoC.
The PCB has VDDH connected separately to 3.3V...
Hi,
I am using nRF Connect SDK, 2.2.0.
I am developing a Central device, which performs the following, in this order:
Enables Bluetooth (bt_enable())
Starts scanning...
Hello,
I am using the gpio_pca95cc.c driver on the zephyr for a nRF5340. I am a beginner at using zephyr OS
I am able to use one GPIO expander but when I add the second...
Hi
I am working with the radio test sample . I am using the RSSi viewer for testing as detailed here . I am guessing that I need two development kits here - one with the...
Hi!
I am trying to use the nrfx watchdog driver on nrf9160 on a custom board.
The application boots, but nrfx_wdt_init() throw error NRFX_ERROR_INVALID_STATE aka. " The...
Good morning, i would want to develop a code in order to have a twi sensor(like an accelerometer) and communicate its data by Bluetooth to another board Nordic, or computer...
I have three nRF5340 Audio boards (PCA10121, 1.0.0). Most of the times, nrfjprog --com won't detect VCOMs on these boards. The VCOMs are there, because I can see them in Device...
I am using the module DWM1001 that includes a nrf52832 and I´m trying to comunicate with BLE via nrf connect for desktop Bluetooth Low Energy but it gives me this error: ...
I want to use app_config.h and the latest driver nrfx. I tried to use the generic sdk_config.h located in nrf5_sdk_17.1.0_ddde560\config but the old config are also defined...
Hi, can i modify USB_MSC example in sdk-17.1.0 to work with SPI instead of QSPI ? as i am working with NAND memory which not compatible with QSPI driver. but it works well...
