We are currently evaluating the nrf9151 via the thingy91X
for our application we need the device to function in areas with no cell coverage and not drain the battery....
Hi
SDK: ncs-v3.4.2
I wanted to compile the lesson as a starting point for a product in non-secure mode with TFM.
I don't have the nrf5340dk but one with the same chip...
We will like to use the Nordic nRF9151 to verify our CP-EDT feature. For that we need an AT command to trigger MO ping but we have not been able to find such command in your...
Hardware: nRF21540 DK
SDK Version: NCS 3.4.0
Problem Description:
Modified the observer sample to scan for a specific device, using nRF21540 DK as the scanner with FEM...
Hello,
Recently we're planning to start our nRF-9151 custom board production.
I've designed my own PC program to confirm all the connectors out application used are doing...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Dear Team,
I have been running two nRF54LM20-DK as Initiator and Reflector for Bluetooth Channel Sounding.
I adjusted the ranging algorithm RAS_Initiator to print Local...
Hello, I want to modify ncs\v2.2.0\bootloader\mcuboot\boot\zephyr main.c code of BLE OTA bootloader, but I need to move its code inside my application firmware repository...
Hi,i use nrf52833, I configured P0.05/AIN3 as a NOPULL INPUT(nrf_gpio_cfg_input(5, NRF_GPIO_PIN_NOPULL);), But I found a weak low level in this IO port. What is the problem...
I am using a nRF52811 with nRF5 SDK 17.1
I have set the PHY to BLE_GAP_PHY_CODED, I believe this uses S=8?
Is it possible to select S=2 with this SDK?
Thanks
Hi,
is it possible to build the nRF5340_audio application for the nRF5340-DK?
What I'm currently is investigating is the possibility of finding and connecting to other...
Hi,
I am software engineer working in Philips.
I am trying to transmit 21 bytes of our payload data (fixed payload length).
I have the following configurations done...
I am attempting to connect a nRF52840dk to Azure IoT Hub using OpenThread and TCP. I combined the azure_iot_hub and azure_fota samples into one project, which ran successfully...
I tried to find simple examples to use SPI in nRF9160DK but all the examples has issues. I did connect using raspberry pi to my modem with no issues but when I use nRF9160...
HI
I had some great support in t his ticket so I will try my luck again.
We want to migrate our application from SPM to TFM. We use SDK 2.1.0. We communicate with the...
Hello to all I am quite lost, I need help to connect an oled to my project. The rest of the stages I have it complete, but my experience with OLED, is limited to arduino with...
Hi,
I am looking for help, we are moving to the 3.2 of zephyr. All our projects are custom boards that run on the previous zephyr version (2.5).
When we compile our...
We use nRF9160 with our board (with Serial LTE Modem 1.9.1). We try to download SLM / Modem firmware via nRF Cloud and we ran into several problems/misunderstandings: 1) First...
Hello,
I can get the distance between four NRF52833 device based on the distance measurement toolbox SDK 1.9.1, but the output rate is a little slow, less than 1 Hz. And...
Hi,
I have a custom board based on nrf52811 and nrf9160. So basically I want to flash those 2 custom board. But I only have ST-Link v3. After doing some research, I only...
Hi Nordic team
I work with 2 NRF5340-AUDIO-DKs (LE audio) and now switch to custom HW on the sink side. Since we only need 3W stereo output we work with 2 MAX98357A
We...
Hi Nordic team
According to this post I eliminated all calls to cs47l63, ina231 max14690 pmic in order to migrate the project to my custom hardware.
After that I get the...
