Hello Nordic Support Team,
I'm experiencing a Bluetooth LE Channel Sounding (CS) issue between a Samsung Galaxy S26+ running Android 17 and an nRF54L15 running the RAS Reflector...
Hello! I've observed that while flashing the nrf9151 modem firmware over USB it always succeeds, but over USB/IP the flashing always fails since the nrfutil tool internally...
Hi,
I have B0, mcuboot and then application as my partitions. We plan to support upgrade of both mcuboot and application.
Based on this below Kconfig snippet, it looks...
Hello I'm developing a project that would communicate with a cellular module using AT-Commands, and voice data using PCM, these cellular modules are always using PCM Short...
What high-temperature storage (JESD22-A103) and temperature-cycling conditions was the nRF9151 qualified to (temperature, duration, cycles)? Your DevZone forum mentions 125...
Hi,
I'm trying to find out how people automate current measurements with the PPK2 beyond doing it by hand in the Power Profiler app.
From the threads here it looks like...
Hi
I am using 4 x AD7410 in each TWI channel, using both TWI ports. So, altogether 8 AD7410s. ( I used the Adafruit breakout boards).
Initially I get the temperature readings...
The BOOT_SERIAL_WAIT_FOR_DFU feature is meant to wait a number of milliseconds (500 by default) for a message via serial comms. If it doesn't receive a message it continues...
Hello,
I have following problem:
I am using a multilink NUS Central. With one peripheral connection everything works fine. But when make a second connection I sometimes...
Dear support
Try to perform DFU OTA on my final target board and have an error state says - "payload(250 bytes) too long for MTU: 249 "during uploading stage, could anyone...
Hi,
I am developing application on NRF52840 with Zepyr 2.1.2 SDK, and I found two problems when using the example scan_adv, as follows:
Executing bt_le_scan_start in...
My team is developing for an nrf52840 on a custom design pre-production PCBA. Up till now we have been using nrf52840dk_nrf52840 in the"Board" field of the "Add Build Configuration...
Hi Team We’re using Nordic connect sdk 1.9.1 We’ve created a vendor service and defined multiple characteristics in same, We are using Nrf connect mobile app to fetch the...
Hi,
I am trying to capture provision packets from the BLE Mesh. I have nRF app for iOS. My iPhone is considered as a provision device, is it possible to provison another...
We are using SDK v1.9.1 with VS Code to develop software for a custom BLE board using the nrf5340 SoC. We also have/use a nrf5340-DK development board.
We generally update...
I want to make a card according to the NTAG213 specification package of NXP.
After I set the parameters, the default value for reading the card content will be NTAG203...
Hi,
We are running Zephyr 2.4 via PlatformIO on a nRF52840 based product. While spamming the nRF with a ton of BLE packets, after about 15 minutes or so we get the following...
Hi,
I have quite demanding SPI device which should send its data over BLE. Thanks to throughput example i was able to achieve maximum transfer speeds for synthetic tests...
Here are some values I got from the terminal:
11011110000000000001000000000010
00000010000001010000010000000011
00000011000000010000001011011110
I do not see the sign...
Good morning,
To my knowledge, the nRF52833 dk as well as the reference designs are FCC certified.
I'm currently searching the FCC IDs for these designs but I'm not able...
Hi
Using nRF52DK + SDK17.1 + S112
I have retarget enabled & using printf to output over UART (no DMA)
What's the best way to check if printf is busy outputting data...
