Hi Nordic Team,
We are experiencing an intermittent Buttonless Secure DFU over BLE issue on our custom hardware based on the Raytac MDBT50Q-1MV2 (nRF52840) module.
Software...
I have been using a NRF52-DK board to develop a BTle solution for the past week. Today, midway through a debug session, the board vanished from my BT interfaces. It also no...
The nRF54L15 Product Specification lists the following PDM feature:
"8 kHz, 16 kHz, 32 kHz, or 48 kHz output sample rate" "Supports digital microphone clocks at 768 kHz...
Hello,
I have just downloaded the NRF52840 Reference Altium Library.
I have noticed that the step file for the component is not symmetrical about the origin.
If I measure...
We're implementing a PAwR (Periodic Advertising with Responses) based onboarding flow for a large fleet of devices (target: 200+ nodes, eventually scaling to 1000s) and are...
Hello Nordic Support Team,
We are using a Fanstel module that integrates the nRF5340 BLE SoC and nRF7002 Wi-Fi companion IC in a single module.
We have manufactured approximately...
Hello everyone, I'm working on a long-distance communication application (>50m).
My hardware is nRF52840, PA/LNA: RFX2401C, ceramic antenna: AN9520-245.
I've achieved...
Hi,
I create two extended adverts, one connectable and one none, (nRF Connect 2.0.0) using the following code:
This works great, but then i want to amend the data...
Hi, I have just started looking at integrating Matter in my devices and am looking to measure voltage. However, there is no cluster under the matter clusters that matches...
Hi,
There is a loose wire on our PDK, The right side is on the cap, but the left side is loose and not clear where it came from. Can you help?
Regards,
Peter
Hello everyone,
In my application, and in samples I have studied, the A-GPS data request starts with the NRF_MODEM_GNSS_EVT_AGPS_REQ event when the modem wakes up/is started...
I'm in the project in which we are trying to implement logging to file functionality to NRF5340 chip.
Following lines were added to config.proj file:
# experimental...
I am trying to write the code for motor controller. I am need to move motor to certain number of ticks based on the given input.
Currently I am using n20 motor for testing...
Looking through a lot of the examples there is a pattern like the following:
Where you capture the success of the function, and on a failure return 1. My main question...
Hi,
We noted in the errata (Issue 133) that the radio performance is significantly degraded if the QSPI is enabled. The suggested workarounds are to 1) lower Vdd to 1.7...
I was working on some project that time i got this error
-- Application: I:/edge-rtos-babelfish-v3/examples/blinky_starter_app -- Found Python3: C:/Users/40025637/software...
I would like to download a new SIM profile on a removable M2M eUICC which is inserted in Thingy91. Can you please let me know how this can be achieved on Thingy91?
Hi,
I have read this ticket which discusses Qi protection to the NFC
I also wanted to better understand if i can protect the circuit with ESD/TVS diode.
It is more ...
Hi all
We are reviewing the homekit HAP function in zephry-based nrf52840 and nrf5340.
It's a rough question, but how much will the binary size increase if the function...
I have a finished product (a very simple wireless remote control with a button) based on two nRF52832 chips and I need to determine whether the communication between the two...
Hello,
I would like to change the default format of a custom characteristic to be a string format. The new characteristic is 8 characters long. This is the code;
Neither...
