Hi Nordic Support Team,
We are currently evaluating the nRF54L05 DFU single-slot sample in NCS v3.3.0.
Our question is: Is it technically possible to configure the single...
Hi,
I'm using the published nRF54L15 DK hardware files and noticed something that I don't understand.
On the nPM1300 section of the schematic and PCB:
Pin 20 ( VSYS...
we are developing solutions with PMIC type=PM1300, we eager to know the internal LDOs PSRR.
i have read 171 page of PM1300 datasheet, but cannot find PSRR data or the PSRR...
nRF54L15 PDM clock runs at ~1/32 of expected (PCLK1M instead of PCLK32M) on a custom board - works on DK
Summary
On a custom nRF54L15 board, the PDM peripheral clock ...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
Hi all — I'm developing a custom nRF5340 development board (Raytac MDBT53-1M) and would value the community's honest read on whether it's worth producing.
The goal is...
Hello All,
I am experiencing strange results when using the TWIM peripheral with and without using the debugger.
Setup :
Keil IDE for development and debugging ...
Hello! I use EK42423-03 and 52833-DK
Previous case
I understand plugging in the SWF connector, Will disconnecting from the PCB antenna and routing the signal to the cable...
Hi,
I have made an emitter (with nRF52833) and a receiver (with nRF52833 too) and i already succeed to receive data and print IQ data from the antenna onboard but now i...
I have tried to install nRF Connect SDK automatically. Although the installation is completed in Toolchaim Manager, the installed sdk is incomplete. After confirmation, it...
I have just bought GeeekPi nRF52840 Micro Dev Kit USB Dongle and would like to install the open boot loader. So for this I have plugged in the Dongle into an USB port on my...
I have been developing for several years with the nRF52832 and 52840 devkits. I have several of each available. One specific 52840 dk seems to have crashed code in the interface...
Hello, All:
I have a problem, when I turn on bluetooth scanning, my UART can't process the received data in time.
When I only use UART to send and receive data, it is...
Hi，
Due to customer demand, the 52810 chip must be used during development. At present, there are too few flash resources in the application layer, and the starting address...
Hello, For our project, we have a gateway which is in a mesh network with others devices. But we would like our gateway to be able to, sometime, connect to a specific device...
Hi, I have some questions regarding the nordic distance toolbox:
Can we use the distance measurement tool with 802.15.4?
if yes, how can the synchronisation be done...
We have queries regarding nPM1100 charging IC, I have mentioned our queries below, Please share your response.
1. What is the main purpose for the s hipping mode and purpose...
I transfer data by ESB between send and receive. And I want to transfer 2 bytes x 10 data that is received by ESB every T[s] to ESB receive (trigger) -> PPI->SPIM, 2 bytes...
I am trying to conduct a basic topology featuring two NRF52840 boards using the Thread Topology Monitor and a thread application using CLI. Once built and connected with J...
With the Bluetooth Low Energy v3.0.1 app within nRF Connect for Desktop, if I use either the nRF52833 or nRF52840 Dev Kit boards as the scanning device it is able to connect...
