I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
Hello Nordic team,
I am testing a plain CoAP telemetry upload from an nRF54L15 DK over Thread using a Raspberry Pi OTBR and NAT64 to ThingsBoard Cloud.
Hardware / software...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
I'm using the prebuilt Aliro stack (libaliro.a, nRF52840), when a session fails inside the library we have no way to get the resulting AliroErrorCode. The stack entry points...
Hello
We are using nRF5340 as our EVK with a 12 antenna array plate(4x4 with center 4 ones not being there). Our beacon uses nRF52833.
We used Nordic's sample codes- ...
Hi,
I am using as settings:
timeslot period: 600 us
data rate: 2M
channel table size: 4
timeslots when out of sync: 8
timeslots per channel: 2
sync lifetime...
When multiple J-Link devices are connected to my computer, whenever I run nrfjprog without the --snr argument, I get a prompt to select the emulator like this:
Is there...
Hi
I am currently trying to get the antenna switching working on the nRF52833 DK
I have an SPDT RF swtich is this pe42423
VDD -> VDD
LS -> P0.26
CTRL -> GND
...
Hi,
I use FDS to save my data. Below is my fds list. All RECORD already have data from factory production.
#define FILE_ID 0x1111 #define RECORD_KEY_TORQUE_0 0x0001 #define...
Hello,
I'm using nRF52833, pca10100..
My project combines the functions of scan and advertising. Each UUID is different and they pair with a different device. I initialize...
Hello, I have got the Acconeer XM122 module (v2.4) and the Acconeer XB122 module (v1.3). The XM122 is connected to the XB122 which is like a breakout board for the XM122....
We customized our own development board based on Nordic's Thingy91 development board. Now it's welded, the circuit works, and we've flash demo MQTT_simple and Asset_cracker_v2...
Hello,
Im a student trying to use the nRF52811 SoC for a project, i need to design a pcb with the chip and a few more things.
I am planning to use the available reference...
Hi,
I need to create a custom dts for a custom board where I need to define the pins used for interfacing to some external devices. The generic "gpio-leds"/"gpio-keys",...
hello Nordic
i have a project than works with nrf52840 and ncs (zephyr)
i want to have the same application running on nrf52832 as well, as part of a single code base...
Hello,
I'm trying to test example "blinky" using nRF52833 board with PCA10100. I used the pca10056 example (10100 don't exist ), and got the "Unknown function at 0x0007521E...
1: The Apple's "Find my function" , How big is the "Find my SDK" ,RAM? ROM?
We can use nrf52820, or nrf52811,or nrf52810 to develop?
We must use nrf52832 to develop Apple...
Hi Nordic Magicians,
I have a couple of general questions when it comes to sending large amounts of data (FAST). Ultimately, I'm looking to transmit data with a throughput...
Hi,
I'm putting together some firmware that takes packets received over SPI and then streams them over BLE. I'm trying to run the BLE at close to 1Mb/s (which is still...
