Hello Nordic team,
I am testing a plain CoAP telemetry upload from an nRF54L15 DK over Thread using a Raspberry Pi OTBR and NAT64 to ThingsBoard Cloud.
Hardware / software...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
I'm using the prebuilt Aliro stack (libaliro.a, nRF52840), when a session fails inside the library we have no way to get the resulting AliroErrorCode. The stack entry points...
Environment
SoC: nRF54LM20 (DK; silicon reports nRF54LM20B ENGB — also reproduces built for the LM20A target)
nRF Connect SDK: v3.3.0-rc2, west v1.5.0
Bluetooth: SoftDevice...
Hello
We are using nRF5340 as our EVK with a 12 antenna array plate(4x4 with center 4 ones not being there). Our beacon uses nRF52833.
We used Nordic's sample codes- ...
Hello All,
I'm new to using Nordic development kit and VSCode but I am running into an issue when I am trying to build a sample application. When I use the template to create...
I am using bt_nus_send to send data via BLE every 1ms. I've noticed that when connection is bad, this function takes a couple of milliseconds to execute, while when connection...
Hello,
I'm currently developing on the NRF9160, a sensor implementation that sends a few 100 bytes every 24hrs.
However, for demo purposes we need to send the payload...
Hi,
I am working NRF DK (NRF52840), when I am trying to flash the program in NRFGOSTUDIO from that it was showing some error that is " No device detected, or readback protection...
Hi, All
I am using VS Code and nRF connect v1.9.1, I try to set some parameters for scan etc. during running. It would be ideal if they can be saved into NVM and loaded...
Hi,
I am conducting a mesh test and it contains:
An android smartphone,
- running nrf mesh 3.1.7 on github
- sending hundreds of bytes packets to the mesh nodes...
Hi,
I am completely new with the development kit nRF5340, I have plugged in the USB and turn it ON, the status after that as follows,
- LED5 is blinking continuesly
...
Hi I have been doing some current consumption measurements using Nordic's Power Profile Kit 2.
The device I am measuring is a custom BLE device that uses the ADC to sample...
Hello, I'm having problems to debug my application when I check the "Enable debug options" in the build configuration. If I don't check this box, I can debug, however, most...
Hello,
I'm working with a little project in NCS 1.9.1, chip is NRF52805 acting as central, connecting to a peripheral that requires passkey and L3 security. Everything works...
Hello,
We are developping based on SDK 15.2 for nRF52 using IAR 8.11 and S132 V6.1.0 as softdevice for central/peripheral application. Bellow is the test scenario explained...
Hello,
I have an application where I send the data I receive over UART, directly to a phone connected with BLE. However, the BLE connection is often not fast enough to send...
I am using nRF52840, SDK16.0.0, Keil v5.18a to developing application. When I changed heap size in Keil C/C++ option, it failed! It can be successful if you change heap size...
Mr Jared, I am sorry. I accidentally pressed the verify button and the ticket(Case ID: 288462) was closed.
To answer your earlier question.
I checked the nrf_drv_rtc_cc_set...
