Hi,
We have deployed some devices now, and we see quite some modem faults popping up.
Could you try to give all info on what you know about these faults we have from...
Environment
SoC: nRF54LM20 (DK; silicon reports nRF54LM20B ENGB — also reproduces built for the LM20A target)
nRF Connect SDK: v3.3.0-rc2, west v1.5.0
Bluetooth: SoftDevice...
Hello
We are using nRF5340 as our EVK with a 12 antenna array plate(4x4 with center 4 ones not being there). Our beacon uses nRF52833.
We used Nordic's sample codes- ...
Title: nRF52840 / OpenThread: how to inject custom IEEE 802.15.4 RX frames into the native receive path?
Hi,
I am working on a test setup around nRF52840, OpenThread,...
While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
Hi all — I'm developing a custom nRF5340 development board (Raytac MDBT53-1M) and would value the community's honest read on whether it's worth producing.
The goal is...
Dear all,
I am now using several pairs of nrf52840DK and nrf connect sdk v1.7.1,and using llpm(low latency packet mode) to send data.
In our system,there are four pairs...
Hi,
I have an issue where sometimes after a restart of our device the nRF hangs on either: ble_dfu_buttonless_async_svci_init() or ble_dfu_buttonless_init(&dfuButtonlessService...
Hello all,
I have 2 problem that I can not understand why.
1) Now cdc_acm isn't working anymore, but until 2 days ago it was working perfectly. I didn't change nothing...
Hi, I'm developing an application tracker device using 2 libuartes, pwm, ble and now I am going to approach reading battery level. After I research on dev zone but I only...
There is already a case on github:
https://github.com/zephyrproject-rtos/zephyr/issues/44586
But essentially we see an issue with nrf5340, where we get random crashes...
HI,
I have tried to read the I2S data by using nrf5340 and I successfully did that. Now, I want to work on the sample with BLE. for that I have made some configurations...
Hi Team,
We have nrf52-DK with version 2.0.0 and we are trying to do power analysis for our application using it. We found a description in nRF52_DK_User_Guide on how...
- I Can't debug nRF52810 using Keil µVision V5.36.0.0 and PCA10026 as segger. I get the message: "No Cortex-M Device found in JTAG chain."
- Using the Programmer v3.0.0...
Hi! I have some troubles understanding the register Erase Protect and before using that I need to understand it more clearly.
I understood that if I activate that register...
I am testing the RTC example in nRF5 SDK v17.1.0.
This example shows LED1 switching at a rate of 8 Hz and LED2 lighting up after 3 seconds.
This is confirmed.
The programme...
Hi Nordic,
We are preparing to validate a product that contains the UBlox BMD-340 with the Nordic Softdevice. We would like to use the Nordic Semiconductor “nRF Connect...
I have a problem with sagger embedded studio I have downloaded latest version for m1 MacBook Pro (I have m1 max version of MacBook) and I have this problem I am using Segger...
I used the central example to scan for BLE devices.
I was able to see the Mac address and UUID in the advertising packet data buffer of 31 bytes. But I couldn't see the...
We are supplying the nRF52840 from 5 V into the VDDH pin. We are not using the USB interface, so VBUS is grounded.
When we apply power to unprogrammed devices and measure...
