Hello Nordic Team,
I am working with an nRF52840 on a custom hardware board and investigating the current consumption in idle condition.
I have tested the same hardware...
Hello Nordic Support Team,
We are developing an LTE-M product for the Japanese market using the nRF9151 and are considering using the Ignion NN03-310 antenna.
We understand...
I am testing the un-unmodified cloud_mqtt_cell_location sample application, and my build configuration is as follows:
SDK: nRF Connect SDK v3.4.0
Toolchain: nRF Connect...
Hello, We have some problem with connection to WIFI AP.
On NCS v3.4.0, once our device has associated with a WPA3-Personal AP, it can no longer
associate with a WPA2...
NCS 3.4.0 - Thingy91X
If I configure the sysbuild with sysbuild.conf
SB_CONFIG_BOOTLOADER_MCUBOOT=y SB_CONFIG_SECURE_BOOT_APPCORE=n
it builds, but on "west flash" I...
I’m using NRF Connect SDK 3.2.4 with the nRF54L15-DK. I’ve successfully used the nrfx_gppi_conn_alloc() and nrfx_gppi_conn_enable() APIs to connect a timer to a GPIOTE output...
Hi, I am starting to get into the Nordic world and want to design my first pcb with nordic chips. I would like to get a review on my schematics and the pcb. I am mostly interested...
Hi,
Nrf52 52840DK,SDK17 S140.
how to broadcasts continuous data? (Continuous broadcasting, with different data each time)
code as follows:
SDKs\nRF5_SDK_17.0.2_d674dde...
I have VSCode 1.63.0 (Universal) on macOS 12.0.1 with ncs v1.7.1 and a board with an nRF52840 MCU. I'm using the "hello_world" example. If I power cycle the board I can start...
Hi,
I'm trying to connect to hook-up a debugger in VSCode to my target but am unable to. The hardware is custom and JLink connects fine with nrfjprog to program and erase...
Hi,
I'm trying to ,create a development environment for Alexa gadget in nRF52832.
here is the thing which I'm using:
1. nRF connect for desktop version v3.9.1
2. Toolchain...
I had a Thingy91 that I think I bricked in trying to upgrade the firmware. I'm able to see the device in desktop programming, but it says erasing then gets to a 100% screen...
Dear, I am new to Nordic. I created a simple project for testing. There is a small fucntion to display "Hello World". After , Re-build Solution.. the memory used is as shown...
Dear community,
I am evaluating the nrf52 chip on the nrf52dk. I am using the peripheral_uart example, built for nrf52810. I have stumbled upon an error which I'm not sure...
In our BLE connections we often receive a BLE_GATTC_EVT_WRITE_RSP event with gatt_status 0x01F2.
Looking at the list of GATT_STATUS values, this must be an error in the...
Hi, based on my previous posts ( 2nd post , 1st post ) regarding the ble_app_uart_c multilink example I now face another issue.
When I run the multilink example on my nRF52840...
Hello,
Until now we compiled our company project using SEGGER Embedded Studio command line tool 'emBuild' that was called from a custom Makefile like this:
But we...
Hi all,
I want to self provision my node. I am using nrf52832 dev board, mesh SDK v 3.1.0, light switch client example. You may wonder why self provisioning, when there...
Hi, I am currently utilizing an app that supports multi link; however, I was only able to get 7 maximum stable connections. My goal for this multi-link is to connect a sensor...
Hi,
I am trying to run the DNS example provided in the Nordic Infocenter as part of the Thread Border Router setup, but it is not working. I am getting "Error 28: ResponseTimeout...
Hello,
I tried to implement the HX711 example from Vidar mentioned here ( https://devzone.nordicsemi.com/f/nordic-q-a/34112/best-approach-to-interface-hx711-with-nordic...
Dear, I am developing first project for self training using Nordic MCU. I want to interface few Buttons, Leds and LCD. I read the Datasheet nRF5340_PS_v1.0.pdf. In it in the...
