Hello, I'm working on a prototype device based on the nRF9151 DK.
HW: nRF9151 DK, nRF9151 LACA A1A Tested with modem_shell sample app, NCS v3.4.0.
Symptom: on boot, "The...
Hi, I have a question with regard to the nPM1100 PMIC and entering ship mode (not exiting it).
If I am interpreting the datasheet correctly, the SHPHLD pin must be held...
Hi Nordic Support,
I am facing an issue where the peripheral registers are not visible in the Keil debugger during a debug session. Only the core registers are available...
Hi:
Use nRF54LM20A_DK.
Use ncs 3.1.1.
And this is source code:
The following error occurred:
« *** Booting nRF Connect SDK v3.1.1-e2a97fe2578a *** *** Using Zephyr...
Hello, I use the NCS v3.3.0 (ncs\v3.3.0\nrf\applications\nrf_desktop). Can the desktop dongle connect to two keyboards at the same time? Development boards: two nrf54lm20...
With SDK 3.3.1 I do not get the <inf> logging messages when building the Hello World app unless CONFIG_LOG=y is added to prj.conf.
Perhaps this is left as an exercise for...
NCS: v3.4.0 Board: custom board based loosely on PAN1783 TF-M not used
Images: - App core: mcuboot, Firmware (main app) - Net core: b0n, ipc_radio
Summary of configuration...
Hello everybody,
I wonder if somebody could give me an example of an easy way to use saadc without using any adc_event_handler for sdk 15.
I'm trying to do it myself from...
Hi,
I connected an external MCU and going to run AT commands sequence by using serial port (UART2).
Can someone provide the sequence of AT commands to get fixed A-GPS...
Looking for advice on reading data from the BL654 UART RX pin which is getting a text data stream from an STM32 micro.
I tried the "peripheral_uart" sample app in Segger...
When "Zigbee Dongle" is successfully connected and communicated with terminal devices, if the terminal devices that have been successfully connected to the network are all...
Hi there
We are trying to modify the MQTT_Simple example to be able to send more info than the status of pressing a button and having a button pressed notification go back...
Hi, I wanted to merge two example projects: "ble_central/ble_app_uart_c" so I have central client application, and a "peripheral/ble_usbd_ble_uart" so I have working USB CDC...
Hi everyone,
Im working and learning for private project CAN bus sniffer which when receive some data trigger some relay...
I have mcp2515_can hw-184 board on which Im...
Hey all I've had some issues with the zephyr installation and have followed the steps for setting up the toolchain. When im building a project from the command prompt it fails...
Dear Sirs,
In my current project I use nRF52 and external ADC. I have to send 14 Bytes each 500us using UART to PC.
It is only one way connection where nRF52840 is transmitter...
I'm attempting to cause the watchdog timer to timeout and activate for a verification test. I'm using Segger Ozone as my debugger. My OS platform is Windows10. I cannot seem...
I wonder what external load (if any) can be connected to the VDD pin of the nRF52805. Reading the data sheet gives the impression it is for internal loads only, but I assume...
Hi,
Today I realized something interesting for our devices: The Update from an older Software Version build with SDK 1.6.X was on it and I updated via AWS FOTA to new version...
Hi,
I am working on the v1.7.0 and I am trying to connect two peripheral with the same services to a central. The first works without any problems:
When I unplug / disconnect...
Hi
I have been experimenting with ncs recently, just trying different things out.
I'm making an application based on the following example (Which is basically code from...
I would like to add dynamically notify callbacks on a given characteristic.
Currently I can only register one callback on the creation of the characteristic:
How can...
