As in subject, psa_aead_finish function generates incorrect tag for AES-GCM when Nordic proprietary library is used.
Works fine with Oberon backend.
Similar problem reported...
Hi, I have a question with regard to the nPM1100 PMIC and entering ship mode (not exiting it).
If I am interpreting the datasheet correctly, the SHPHLD pin must be held...
Hi Nordic Support,
I am facing an issue where the peripheral registers are not visible in the Keil debugger during a debug session. Only the core registers are available...
Hi:
Use nRF54LM20A_DK.
Use ncs 3.1.1.
And this is source code:
The following error occurred:
« *** Booting nRF Connect SDK v3.1.1-e2a97fe2578a *** *** Using Zephyr...
Hello, I use the NCS v3.3.0 (ncs\v3.3.0\nrf\applications\nrf_desktop). Can the desktop dongle connect to two keyboards at the same time? Development boards: two nrf54lm20...
With SDK 3.3.1 I do not get the <inf> logging messages when building the Hello World app unless CONFIG_LOG=y is added to prj.conf.
Perhaps this is left as an exercise for...
NCS: v3.4.0 Board: custom board based loosely on PAN1783 TF-M not used
Images: - App core: mcuboot, Firmware (main app) - Net core: b0n, ipc_radio
Summary of configuration...
Hi all,
I am currently using Raytac dongle https://www.raytac.com/product/ins.php?index_id=89 with connectivity FW on the dongle and pc-ble-driver version 4.1.4 and sd_api...
Hi,
I am trying to edit my bootloader (buttonless USB DFU).
I want to add a button to exit the bootloader and return to the app.
The problem is that the gpiote interrupt...
Hi Team,
We are on the Pre-Production stage of our Product, which uses the nRF52840 (forBLE) with the FEM nrf21540(new)
We are aiming to get power out of 20dBm.
To get...
I observe issues when trying to use the datetime lib on the board qemu_x86.
I get the following page fault:
This is reproducible and happens shorty after successfully...
Hello all,
I am migrating our FW NRF52832 from SDK11 to SDK17. (Actually I am starting from scratch on 17). Here I have two characteristics with only read properties (e...
To the kind attention of Nordic support team,
About nRF52833 product specifications (8. recommended operating conditions)
"Note: The on-chip power-on reset circuitry...
Hi,
I'm trying to run a pc-ble-driver on Arm64 arc
I've compiled the pc-ble-driver to arm 64 from this release: ARM64-linux pc-ble-driver origin/release/4.1.2
I used...
Hi,
I'm currently working on a way to connect raspberry pi as a gateway into the nrfcloud. For this case, I used nrfcloud/gateway-raspberry-pi. Neverless, when I tried to...
I am developing a product using nRF9160 and found the power consumption is higher than the datasheet. So I want to use Matlab ti simulate the circuit to see where the error...
I am currently trying to implement a Thread functionality on an nRF Dongle connected to a windows machine. Its intent is to be able to recieve messages from other thread components...
Hello Nordic team,
I have a nrf9160 powered from a 3.8v bench supply.
I also have a usb to uart cable , with uart wires going into NRF9160. Usb side, plugged into my computer...
Hi
1、 The following table does not indicate whether the QDID belongs to 5.1 or 5.2.Are the QDIDs of softdevice classified as Bluetooth 5.1 or 5.2?
2、The following qdid...
