Subject: nRF9151 – EU coverage of mfw 2.0.2 and antenna gain (Schréder Sense One)
Dear Nordic
I'm working on CE and RCM certification for Schréder's SENSE ONE smart-city...
We have an nRF54L15 (QFAA) board, acting as an I2C target ( TWIS30, P0.00/P0.01, address 0x42, 100 kHz ) for an ESP32-S3 through a TCA9406 level translator.
Flow:
Between...
Hello, I am requesting a schematic review of my bluetooth microphone system. I've used the spec sheets as well as audio DK hardware reference material to design these schematics...
We are seeing very high defect rate when installing this part on boards: insufficient solder, solder bridging. When we look at the pads under the microscope, we are seeing...
Hello,
We have an issue. Our device is a custom board based on the nRF9151, and we use it in Latvia. Two network providers are available for our Onomondo SIM card: one supports...
Hello,
We are developing a product based on the nRF52840. According to the blog post nRF Connect SDK gets Long-term support with version 3.4.0 , NCS v3.4.0 declares the...
Subject: Request for Optimal Battery Solution for nRF54L15 Matter End Device
Hello DevZone Team,
I am opening this ticket to identify the optimal power solution for my...
Hello
When we evaluated nrf52833 (using DTM), everything was normal at 1M, 2M, LR. However, during CTE evaluation, after the serial port sends a configuration command, the...
Hi,
I'm on SDK 17.0.2 and SD 340. Trying to combine BLE services as Central server with BLE HRS_C example. The idea is to read the BLE HRM and also to be able to connect...
Hello,
I am trying to enable RTT instead of the default UART output of the nrf91dk AT client code example. I am using Segger Embedded Studio V5.34 with Nordic nRF Connect...
when using nRF5 SDK Release 1.4.99 the the projects open some have errors that prevent it from building for the nRF5340,
when I attempted to use nRF5 SDK 1.5.0 or 1.5.1...
Hello, everyone,
I got a Thingy91 and I would have liked to be able to measure the current that passes through the NB-IoT modem, for that, I followed this tutorial :
https...
Hi dev team,
I am using a Thingy91 device along with the NCS v1.5.1.
I used the AWS FOTA example for firmware upgrades and I integrated the example in my code.
The FOTA...
Hi,
I am trying to implement DALI-104 (IEC-62386:104:2019) on top of openThread protocol.
I am using Thread: CoAP Client and Thread: CoAP Server and want to configure...
Hi Nordic Dev Team,
I am trying to send my log data from my flash memory into Android Phone. I followed this example :
github.com/.../nRF5x-custom-ble-service-tutorial...
Hi,
Setup:
DK : nRF-52840 PCA 10056
IDE
SDK : nRF5_SDK_17.0.2_d674dde
Coding Language : C
Please find 5 queries listed below.
1) My plan is to automate BLE...
In a .c file ,code like below (build a image using nrf5340dk_cpuappns) :
#include "nrf_gpio.h"
#define SPIM2_CS NRF_GPIO_ PIN_MAP(0,15) #define SPIM2_SDO NRF_GPIO_ PIN_MAP...
The picture is the audio data processed by software, which is driven from nrf52832 and nrf52840. The first audio is the data of nrf52832, which is normal. The second audio...
Good morning,
I need to perform precompliance tests for my board based on the nRF52840.
I read in this ticket:
https://devzone.nordicsemi.com/f/nordic-q-a/59242/certification...
hello :
We have a device that is ble master-slave and includes OTA function.
1. When the device adds a watchdog, the watchdog callback is triggered (wdt_event_handler...
I am new to IoT development, and am working with the Nordic Thingy:91, and nRF9160 development kit as a starting point for development. Is there a preferred operating system...
