NCS 3.0.1
nrf52840
nrf21540
I have read several tickets regarding antenna diversity and BLE. It does not seem to be supported for BLE. What about Thread?
I have read...
Affected: nRF Connect SDK v3.4.0; the same code is on main as checked on 2026-11-11 ( subsys/net/lib/nrf_cloud/common/src/nrf_cloud_codec_internal.c , subsys/net/lib/nrf_cloud...
We are currently using an NRF54L15 with TF-M on NCS 3.4.2. We have a custom secure partition, and want it to own a persistent P-256 ECDH private key and derived AES-128 key...
When I connect the two-pin battery and short pin1 and pin2 of P1, I am unable to get the battery voltage at J1 AND WHEN I LEAVE THE PINS UNSHORTED FOR P1, THEN I AM NOT GETTING...
I have connected the correct 47K res for VSET1 but I am not getting 1.8V, instead I am getting 2.3V I am getting the correct output for BUCK2 as 3.3V I have checked the resistor...
Hardware: nRF21540 DK
SDK Version: NCS 3.4.0
Problem Description:
Modified the observer sample to scan for a specific device, using nRF21540 DK as the scanner with FEM...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Hi,
I get BLE_GATTS_EVT_WRITE with connection handles 16 and 19 which seems to be some defaults of the softdevice.
Can you explain the source and usage of these connection...
Hello
I am working with aws_iot sample and over this I add gps functions (handler and work init) belong to agps sample, I probe AT%XMONITOR command and show me this
...
I build the example and download to PCA10040,but there no log print in RTT, and I debug in keil mdk, I found the program does not step into main function.
How to run this...
I have an application that requires that timestamps be 64-bit epoch to the millisecond. I'm currently using a Timer peripheral to track 1ms and increment a 64-bit counter...
Hi,
How can I make the device generate random address periodically? I searched on the forum and found people mentioned BLE_GAP_ADDR_CYCLE_MODE_AUTO when call sd_ble_gap_address_set...
Hi.
I have a product that acts as a peripheral, and bonds with centrals that are typically smartphones. Normally the peripheral uses a whitelist to only connect to bonded...
So I noticed the program goes into a state where it's stuck on NRF_BREAKPOINT_COND , which happens after getting into the following writeToLogger () template function. If...
Hello,
I am evaluating NCS 1.5.99 zephyr's sample"periodic_adv"and"periodic_sync"with two nrf52833 DK. The sample "periodic_adv" runs normally on nrf52833 DK.But the sample...
Hello,
I've been trying to use Zigbee Endpoint Logger for the light_bulb and light_switch sample. But I can't make it work. I've been looking through the quetions on this...
Hello guys, i want to implement nrf5-calendar-example in nrf51822 with SDK 12.3.
This library can use RTC0/RTC1/RTC2. But i have only RTC0 and this RTC0 is for SD (am i...
hello,
if i want to connect to a peripheral device with strongest RSSI. I need to get the RSSI before connecting.
and i know i can get the RSSI from event of BLE_GAP_EVT_ADV_REPORT...
I'm trying to read the values from the DS1307 RTC through TWI. I've established a connection with the device but am not sure I'm using the nrf_drv_twi_rx() function correctly...
Hi,
I'm trying to run the peripheral heart rate service example on a custom board using the internal 32kHz RC oscillator. However, the code hangs when soft device is enabled...
