Subject: nRF9151 – EU coverage of mfw 2.0.2 and antenna gain (Schréder Sense One)
Dear Nordic
I'm working on CE and RCM certification for Schréder's SENSE ONE smart-city...
We have an nRF54L15 (QFAA) board, acting as an I2C target ( TWIS30, P0.00/P0.01, address 0x42, 100 kHz ) for an ESP32-S3 through a TCA9406 level translator.
Flow:
Between...
Hello, I am requesting a schematic review of my bluetooth microphone system. I've used the spec sheets as well as audio DK hardware reference material to design these schematics...
We are seeing very high defect rate when installing this part on boards: insufficient solder, solder bridging. When we look at the pads under the microscope, we are seeing...
Hello,
We have an issue. Our device is a custom board based on the nRF9151, and we use it in Latvia. Two network providers are available for our Onomondo SIM card: one supports...
Hello,
We are developing a product based on the nRF52840. According to the blog post nRF Connect SDK gets Long-term support with version 3.4.0 , NCS v3.4.0 declares the...
Subject: Request for Optimal Battery Solution for nRF54L15 Matter End Device
Hello DevZone Team,
I am opening this ticket to identify the optimal power solution for my...
Hi,
I am trying to program new chips. I have made the following connections:
Chip J-Link ------------------------------ Gnd Gnd SWCLK SWCLK SWDIO SWDIO VDDH 5V (External...
Hello:
We have a BLE application on an NRF52840 with SD 140 and SDK 1.5.3. Our device acts as a BLE peripheral with bonding and LESC, and we additionally use block level...
Hi,
We have designed the custom PCB where 32.768 kHz crystal oscillator is required. Some how we have managed the component (MFR PART NO. TF325J32K7680 ) suggested by Nordic...
Hi, I came across a forum post that NRF51 had an issue with noises in SWCLK signal.
For the design, do I need to attach an external pull down resistor in design? If so,...
Hi good evening,
i am working on a project that requires ble transmission between 2NRF52dks and one of them is connected to a PC and apart from receiving data from another...
Hi Devzone,
I have 2 question about Thingy 91:
1) When I come to area that don't support NBIoT or LTE-M, Does the Thingy 91 connect to cloud (nrf cloud, mqtt broker,....
We have developed an Android application for a customer (Ibiza) which makes use of nRF's Android-BLE-Library ( https://github.com/NordicSemiconductor/Android-BLE-Library ...
I defined a timer and start the timer when application open gps, it can prevent the timeout of star search failure; When the gps search star successful, I will turn off the...
Hi,
Now I using the nRF5_SDK_for_Thread_and_Zigbee_v4.1.0 to develop the zigbee function on nRF52840,
I am using the light control Example,
it provide two examples to...
Hello,
I'd like to know how to interface with the SDK libraries(as a "beginner") and ask how do you approach such a thing and learn how to use it? let's take for example...
Hello,
I have an xon / xoff flow control implementation with nRF52833 DK.
The setup is the nRF52833 DK is connected to the computer through USB cable.
A python script...
So far, since UART has been working well, now, we are switching from UART to RTT to remove UART port connection from our PCB design.
However, the output to RTT is working...
Hi, I am trying to use the nrfx_pdm driver with a microphone connected to the NRF52840DK. Currently, it is working but I cannot quite understand how handlers are functioning...
Hello
I want to flash my simple coap server code in nRF52840-Dongle using USB DFU mode with nRFConnect but I did not find COMPORT/ Any Jlink Device after put donge in USB...
