I am using the nRF5340 development board to program the LBS example from the NCS SDK2.7. After system-off, the current is still several tens of microamps, which differs from...
When trying to add the device to the Nordic Cloud Device Management interface, I get the following error.
"There was an error adding your device: No device found for this...
Hi,
I am using the heart rate sample.
I have connected ground to ground, 3.3v to vdd, SDA to pin 26 and SCL to pin 27. I have 4.7k pullup resistors on SDA and SCL. When...
Hi,
I am developing a custom PCB based on the nRF52840 and am currently trying to flash/debug it using an nRF52840-DK (PCA10056) as an external debugger.
connected devices...
So I have two questions. My first is on the impedance matching network on different pcb stackups. So wouldn't I need a different matching network for a different pcb stackup...
We use the NRF Mesh Android Library (and are developing with iOS version as well). An issue that we are running into on a small number of devices is that the library things...
Hello together,
i am trying to connect to an Azure Blob Storage Container via https with a nrf9160 but I am only getting error 111 (connection refused). For that I am...
Hi DevZone,
I want to perform USB bulk transmits to a host device while using the app_usbd library. I am using SDK 15.3 and the s140 soft device is enabled.
I have found...
Hello Nordic Team;
The Vdd value range for the nRF9160 is 3.00 V to 5.5 V. We will use li-PO battery in our system. Can I power the nRF9160 directly from the battery without...
Hi,
I am using Nordic thingy 52 for my application, Now I need to blink LED for 5 seconds on Board when ever a condition is satisfied. But in schematic of Nordic thingy...
Board: nRF51-DK (nRF51422 chip)
SDK: 12.3.0
SoftDevice: S130
Compilation settings
Optimization level O1
Debug information generated
I have seen lot of...
Hi.
I am going to make my own PCB with nrf52832.
Before making it, I have to check debugging through P20 in nrf52832 DK.
I have two nrf52832 DKs with SDK17.0.0....
Platform: nRF5340-DK
Tools: I am using SDK 1.5.0 (but seen on earlier SDKs too)
Configuration: Using high speed spi pins whether for SPI1 or SPI4
If I use SPI1 I see...
Hey guys i wanted to ask you for help on IOS BLE i am currently seeing that nRF Connect seems to work fine over BLE Connection with some devices on Android and as far as i...
Hi,
I'm using NRF52840 in order to connect to a mobile app via BLE.
When connection to IOS, I have an event called BLE_GAP_EVT_PHY_UPDATE_REQUEST.
This event handle...
Hi,
Greetings!
We are exploring nRF9160 SIP DK and Thingy91.
Here we have understood that it has GPA and LTE-M.
We wish to use it for India region in moving objects...
We are using the advanced UARTE library to get advantage of EasyDMA to receive data from a LTE module.
We also implemented hardware flow control. THe problem is that the...
Hi fellow devs:) I'd really appreciate some advice on this please. I've come to a bit of a dead-end. Hopefully you can spot a mistake I've made. I am trying to produce a low...
Hi,
-I have a custom board using nrf 52832 and I have interfaced sensor using an SPI interface. -I am using SDK 15.2.0 and SPI driver. -I am collecting raw data and send...
Hi, When I test the SPI with extern flash W25Q64, The SDK default configuration seems to be too low powe, After SPI initialization is complete, The GPIO drive is configured...
Hello All ,
I want to use nRF 52810 Bluetooth feature in one of my application. The application is supposed to be highly power optimized. Sharing below some details about...
