Hello,
I have 2 Memfault projects that I'd like to rename, but I can't find any way to do this through the web app, and the API authorization keeps getting rejected (tried...
Hello, I'm working on a prototype device based on the nRF9151 DK.
HW: nRF9151 DK, nRF9151 LACA A1A Tested with modem_shell sample app, NCS v3.4.0.
Symptom: on boot, "The...
Hi, I have a question with regard to the nPM1100 PMIC and entering ship mode (not exiting it).
If I am interpreting the datasheet correctly, the SHPHLD pin must be held...
Hi Nordic Support,
I am facing an issue where the peripheral registers are not visible in the Keil debugger during a debug session. Only the core registers are available...
Hi:
Use nRF54LM20A_DK.
Use ncs 3.1.1.
And this is source code:
The following error occurred:
« *** Booting nRF Connect SDK v3.1.1-e2a97fe2578a *** *** Using Zephyr...
Hello, I use the NCS v3.3.0 (ncs\v3.3.0\nrf\applications\nrf_desktop). Can the desktop dongle connect to two keyboards at the same time? Development boards: two nrf54lm20...
With SDK 3.3.1 I do not get the <inf> logging messages when building the Hello World app unless CONFIG_LOG=y is added to prj.conf.
Perhaps this is left as an exercise for...
Hi,
I'm trying to set up SEGGER SystemView on our custom nRF5340 board for debugging purposes using the SEGGER SystemView application.
Below is the configuration I'm using...
Hello,
Our project using NRF5 SDK V17.0.2 require SBOM (Software Bill of Materials). Do you know if there is one readily available? If not, do you know how to obtain/generate...
Hi, I am new to blue tooth mesh, but want to develop a test system with blue tooth mesh. Eventually I would like to be able to create a blue tooth mesh network to provision...
I would like to modify the Matter: Light Bulb sample project, which comes as a dual Matter + AWS integration all running on WiFi. I would like to modify this project so that...
i write a simple code to show "hello world" at TFT adafruit 2.8'' 1947 over spi "ili9341" i flashed the code but i think it's stack at "device binding in Zephyr" but nothing...
Hi DevZone,
I am trying to add a 3rd party library (consisting one c file and 2 header files) into a SDK example in Segger embedded studio.
I don't know the exact procedures...
Making a transition from my prior nRF52840, SDk 15.3, FreeRTOS based projects to nRF54L15, nRF Connect SDK 3.0 based project. My projects before are using DFU, USB, RTT, And...
Hello Nordic Team,
I have a working project that uses BLE to communicate with a mobile app, and I am now looking to integrate Google Fast Pair as an additional feature....
I have a simple custom board using Fanstel BM15C module. It is connected to DEBUG OUT connector of the nrf54l15-dk.
I am using VS Code and nRF Connect extension pack, SDK...
Hello
since i could not post a ticket (got the message 'could not create a ticket'), I try it again with almost no text here but added the content in a txt-file.
Hope...
Dear Nordic-Team,
we are currently trying to add CSR creation to our project which worked quite fine by implementing it similar to the psa_crypto sample.
Unfortunately...
Hello Nordic Team, We are developing a wearable health device using the nRF5340-DK and Zephyr RTOS. As part of the BLE communication design, we intend to use **Security Level...
I am looking at options to integrate the ADXL 367 accelerometer into my firmware project (nRF Connect SDK 3.0.2). I see the sensor is supported by Zephyr and has a complex...
We are hardware manufacturing company currently developing AMI solutions with Wirepas integration. Do any of your partners offer smart meter solutions that use Wirepas and...
Before i inserted in my code to use ppi + gpiote + spim usb serial device port worked properly, it connected normally, but now it doesn't connect the port at all, did i create...
