Hello,
I have 2 Memfault projects that I'd like to rename, but I can't find any way to do this through the web app, and the API authorization keeps getting rejected (tried...
Hello, I'm working on a prototype device based on the nRF9151 DK.
HW: nRF9151 DK, nRF9151 LACA A1A Tested with modem_shell sample app, NCS v3.4.0.
Symptom: on boot, "The...
Hi, I have a question with regard to the nPM1100 PMIC and entering ship mode (not exiting it).
If I am interpreting the datasheet correctly, the SHPHLD pin must be held...
Hi Nordic Support,
I am facing an issue where the peripheral registers are not visible in the Keil debugger during a debug session. Only the core registers are available...
Hi:
Use nRF54LM20A_DK.
Use ncs 3.1.1.
And this is source code:
The following error occurred:
« *** Booting nRF Connect SDK v3.1.1-e2a97fe2578a *** *** Using Zephyr...
Hello, I use the NCS v3.3.0 (ncs\v3.3.0\nrf\applications\nrf_desktop). Can the desktop dongle connect to two keyboards at the same time? Development boards: two nrf54lm20...
With SDK 3.3.1 I do not get the <inf> logging messages when building the Hello World app unless CONFIG_LOG=y is added to prj.conf.
Perhaps this is left as an exercise for...
Hi,
I am using 2xL91 battery for powering board with sensor and camera. In general there is no fluctuation when we use sensor which is taking about 4.2mA and in idle mode...
Hello,
I am attempting our custom hardware based on an nRF52 chip.
nrfjprog returns the following error message:
ERROR: JLinkARM DLL reported an error. Try again....
Dear Sirs,
We are currently considering to put nRF5430 SoC in our next generation gaming device. One possibility to develop the firmware for nRF5340 SoC would be to use...
Hello,
I have just started learning nrf. I have an nrf52832 board and I want to get and set time using app.
I have seen this https://devzone.nordicsemi.com/f/nordic-q...
Hello
I would like to change the "Company ID" in my application so that it is no longer Nordic's (my application is based on the ble_thread_dyn_mtd_coap_cli example). I...
Hello
I'm contacting you because I'm having a problem connecting to devices that use the ble_thread_dyn_mtd_coap_cli example. Actually, I have no problem when I connect...
Hello all,
I am working on nrf52832 and i need to use the nrf_crypto librariy. The example uses nrf_crypto_aes_crypt and nrf_crypto_aes_finalize function. Although they...
As title, I would like to measure an API function execution time. First method is to print the timestamp before and after the API and the second is to use GPIO and measure...
Hi!
We are developing a board with nRF9160 and want to use it on NB-IoT mode.
The development is made in Romania, Cluj-Napoca and here we have no problem with it. Even...
hello sir/madam .
i am going to implement the code to master and slave clock communication , iam connecting the one nrf52 module to the master clock (through wire controller...
Hello,
I guess it is a simple problem, but I am new to the nrf world, so here is my issue:
I want to use this code to switch on a LED by pressing the on board button...
Hello, I am starting a project and I want to know what is the best way to achieve this. I am using nrf52832, I have the DK as well as custom board. I want to receive an image...
Hello Noridc Support Team and All members,
I am new to BLE development.
I am using the nRF52 development kit and the SDK v17.0.2
My intent is to send the sensor data...
I was studying the Wireshark BLE sniffer packet parsed data for a "Find By Type Value Request" and noticed that the Value was not parsed as Little Endian so it was given as...
