Hi,
I noticed in the nRF54L QFN48 reference design, for the NRESET pin, there is an RC filter (1Kohm series R and 3.9pF shunt cap). What's this for and is it necessary?...
Hello,
I am using a nrf5340 dev kit. When I use SPIM the output from the pins gives the correct hex values but the output's amplitude is only around 100-200 mV. I know that...
Hi,
I'm using the nRF52840 with the SoftDevice for BLE. In my system, it's primarily a BLE transceiver controlled via SPI by an external TI MSP430. We're considering implementing...
Hello,
I want to request AGNSS information from nrf cloud services using my nRF9151DK board. As a first step, I flashed the nRF Cloud multi-service application onto my DK...
Hello,
I just received my Thingy:91X which I purchased through DigiKey. I am trying to connect it to hello.nrfcloud but I keep getting the following message: " The fingerprint...
With reference to the Thingy:91x reference design, I see that the LNA (SKY65943-11) on the GPS signal path is powered by one of the switching converters from the nPM1300:...
Hi,
I'm using cdc_acm to create two COM ports on a PC -
// USB support
& zephyr_udc0 {
cdc_acm_uart0: cdc_acm_uart0 {
compatible = "zephyr,cdc-acm-uart" ;
...
Dear people,
I use a pca10056 (alternatively the pca10059 dongle) and have compiled the connectivity firmware as described on the github page (release 4.1.1).
The only...
I use nrf5_SDK_for_Mesh_v3.2.0_src\examples\serial and board pca10040.
Supported commands.
In [2]: for i in range(0, 10): send(cmd.Echo("Hello: " + str(i))); time.sleep...
Hi, I'm reading the nRF5340 OPS v0.5.1 document and in section 3.2 ("Memory") there is a reference to "256kB of peripheral RAM". However, the document doesn't explain what...
Hi there,
I'm working on nrf82382, try to use COMP function to monitor the voltage of AIN0(p0.02), but seems not working, no example for the COMP. and then I found the...
We enable TX notification of NUS service with bonded iOS (iPhone), iPhone constantly sends TX_READY command until disconnect.
Can you confirm this is correct behavior. ...
Hi, I am working with the adxl362 sensor and the nrf9160 SPI example ( https://github.com/Rallare/fw-nrfconnect-nrf/blob/nrf9160_samples/samples/nrf9160/spi/src/main.c ) and...
Hi, I am working with the adxl362 sensor on the Thingy91 and I want to set the trigger of the sensor to a specific value.
In the datasheet ( https://www.analog.com/media...
Hello everybody! I'm developing an application using CMSIS DSP library, so i included about 20 math files and using finctions from these files. After compiling i get a linker...
Hello Devzone,
I'm designing a custom board solution that drives a motor using a nRF52832. The board is powered with 4 x AAA batteries and a 2.5V LDO (STLQ50C25R) is used...
My company has a product that is running on the nRF51, with firmware written in SDK9 and sd310. I've been tasked with developing a path to update them to SDK 12.3 and sd130...
Hello nordicsemi community. I'm trying to use the SPIS example provided in the NRF52 SDK to receive data from another SPI master running on an FPGA. I modified the code to...
Hi,
I'm trying to write data to flash as shown in example under nrf5_sdk/examples/peripheral/flash_fstorage, with identical steps.
However every time I call the nrf_fstorage_write...
HI,
I am using nrf52832 with sdk15.2.0 and softdevice s132. I face some issue related MAC address of nrf52832.
when I reset the sensor MAC address of the sensor change...
I am trying to step through the code of an example of the nRF5_SDK_16.0.0 on the nRF52 DK board.
I downloaded the latest version of Segger Embedded Studio (v4.30c) and I...
Hello,
I have a brand new Thingy 91 running the default asset tracker application connected to nrfCloud.
I wanted to build the asset_tracker myself and upload it to validate...