Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hi, I am trying to understand the Friend and LPN behaviour. For that I am refering to nRF sample application light" and "light_switch". Below is the setup details: 1. On one...
Hello,
We have an old working product which is developed in nRF5 SDK v11.0.0. We want to add nfc type 4 tag part in our product.
In SDK 11 there is only support for nfc...
I am looking to understand the state of a pin after calling nrfx_saadc_channel_uninit(channel);
Does it simply return to the last configuration state of the GPIO or something...
Hello, I am using a nRF51822 chip to communicate with a sensor. The sensor continuously outputs its reading via UART every couple of seconds. This is what I am currently doing...
Hi, I'm trying to migrate from the nRF9160 DK to our own board, and I'm having some trouble getting the west build system to play nicely. I've essentially started with the...
Hello everyone.
I have been working on a project that involves DSP and BLE on nRF52832.
The firmware needs to sample an accelerometer signal every 1ms with high accuracy...
Hello,
I am working on nRF9160dk. I have interfaced a GNSS sensor with nRF9160 using UART and receive the data continuously. When there is an interrupt, this data is send...
Hi All,
I have developed application which will detect key press and perform he respective task ,using the S132 (nrf52) with button-less dfu project (SDK15.3)which
includes...
Hi everyone
I have been facing some issue while allocating memory using nrf_malloc function on nrf52840.
I am giving a size parameter of 8 bytes inside the nrf_malloc...
Hi,
We are working on Nordic NFC antenna modification - it has to be lengthened by 15 mm to fit in our case.
1. Question - is the green marked part curved just to gain...
Dear community,
We are testing a nRf8001 Implementation, DTM transmitter Test with continuous unmodulated carrier.
In the PS 1.3 / 22.5 i saw that the dynamic data is...
Hi,
I'm trying to validate a device which uses VSP to communicate. It has a custom service with only 2 characteristics. 1 to Write (TX) and the other Notifies (RX).
When...
Hello :
I come from STM32 programming and I am new to Nordic device programming.
for nRF52840 DK, I am looking at the ble-blinking example and try to understand Softdevice...
i am working nrf51822 and SDK V10 SoftDevice S110. I was using some old version of nrfutil ( dont know version ) to generate zip file, that was working fine. when i start...
Is there a way using the API to utilize all 31 bytes of advertisement data for a user application? I'm porting an application, which sends data in advertisement packets, to...
Hi,
I need nrf_malloc and nrf_free for my application but I cant find which files should I include to be able to use thees functions.
Thank you very much
