I want to use the Softdevice Controller without a crystal on the RTC. I configured my project with
Advertiements look fine, but interaction with a BLE central either throw...
Hi everyone,
These days I'm evaluating the Nordic nRF5340 to manage audio from two microphones to one dongle station. To achieve this, I configured two nRF5340s as unicast...
I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
I'm using the prebuilt Aliro stack (libaliro.a, nRF52840), when a session fails inside the library we have no way to get the resulting AliroErrorCode. The stack entry points...
After installing nRFgo Studio v1.17.1 on Windows 7 64 Bit (using the administrator account), I get an error message in the Log section just when I start the program:
"JLinkARM...
I'm using SDK 14 and trying to build the ble_app_buttonless_dfu example. I'm using Linux environment, so gcc for building. When I try to build the example I'm getting an error...
Hi, I was just wondering why there is a "nrf_delay_ms(200);" in the SPI Master example in SDK 16.0.
Here is the code in the main function where it is located :
while ...
Hi Support,
Now I am developing over Nordic 52840 DK (PCA10056). My environment as below,
(1) upon SDK (nRF5_SDK_15.3.0_59ac345)
(2) softdevice s140_nrf52_6.1.1_softdevice...
Hello,
I am using the nRF SDK for Mesh v.3.1.0. To achieve periodic publishing, I set p_pubstate -> publish_period . step_num = 1 instead of zero in the configure step in...
Hi,
I plan to design my own hardware based around nRF9160. Prior to this, I want to verify that I can use the nRF9160DK as a debugger for my own board. As an initial test...
Hello,
We would like to develop a wireless sensor network using the 802.15.4 stack in nRF SDK.
I wanted to know if it is possible to port the existing 802.15.4 example...
Hi,
I'm evaluating the Raytac MDBT50Q devkit, using nRF52840-DK to program it. I'm testing the system with SDK project nRF5_SDK_15.3.0_59ac345\examples\ble_central\ble_app_uart_c...
Hi. I am currently evaluating nrf9160 on a Thingy 91 board and have the environment for the asset_tracker application up and running.
I want to be able to handle JSON messages...
Hi,
I would like to have a system such as follows:
Taking sensor data storing it locally till around 100 samples (Once per second)
Log this data to the SD with a time...
Hello,
I was wondering if there are production ready fully pre-certified modules for the nRF91 Cellular chips? Like what Rigado (u-blox has it now) made with the BMD series...
Hi,
I would like to use the nRF52840 dongle to connect to 8 devices using Ant+ and to around 8-24 devices using Bluetooth.
Is there a maximum number of devices of Ant...
Hello to everyone,
I've just started playing with NRF52 DK (NRF52832 SoC). It is my first time with ARM MCU. I've had prior experience with atmega328p and MSP430. Although...
Just ordered 2 Thingy52 and could only connect to one of them. Both boxes mention 1.1.0 2019.34
I used the code from https://github.com/NordicPlayground/Nordic-Thingy52...
