Hello Nordic team,
What is the image frequency of the nRF54L15 receiver?
We need this information for Bluetooth SIG RF-PHY qualification (RFPHY/RCV/BV-03-C, RFPHY/RCV...
Our prototype is back. At first, I used NRF Connect to flash it, but the official PC software couldn't flash the firmware. I followed the wiring instructions: (1) connect...
We are developing an application based on the nRF9151 using NCS 3.1.1 and modem firmware mfw_nrf91x1_2.0.3 .
We would like to use Proprietary PSM to control the modem's...
Hello, The nRF9151 hardware design guidelines (power sequence) require VDD_GPIO to be applied at least 6 ms after VDD and ENABLE, after the hardware boot. In our design a...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Dear Team,
I have been running two nRF54LM20-DK as Initiator and Reflector for Bluetooth Channel Sounding.
I adjusted the ranging algorithm RAS_Initiator to print Local...
Hi,
I'm trying to find out how people automate current measurements with the PPK2 beyond doing it by hand in the Power Profiler app.
From the threads here it looks like...
Hi,
I am usinf nrf52832 development kit and I want to establish a secure connection between central and peripheral device.
I know one way is using pairing mechanism I...
Hi,
I am using mesh SDK 4.0.0 and nRF SDK 16.0.0. I ported the ble_app_uart_coexist example from mesh SDK to build OK for pca10056 board (nRF52840) by following the instructions...
I'm attempting to receive SMS in eDRX mode. It succeeds when nRF9160 device is left in a place without moving it.
However, when I move it to a far place like a few kilometers...
Hey..
I'm using the nRF52840-preview evk, with the Arduino camera plugged into the side connector. PCA10056_USE_FRONT_HEADER is set to 0, and I'm using the SES project....
Hello, guys!
I recently started playing with nRF9160 SiP module. nRF Connect SDK is properly installed and I am able to build the code and download it properly. I also spent...
I have a nRF52832 Breakout Board, in which i programmed using arm cortex debug connector, using Segger Emmbedde Studio. I uploaded one example from nRF5_SDK_15.3.0, the propramm...
Hello;
we are having a communication issue(a BIG one at this point) that we are experiencing with our BLE 4.0 tablets. Our device(has NRF52832) is designed to communicate...
I noticed some weird behaviour which I can repeat to do with not being able to register after reading back the ICCID.
The following after the list of commands I run on bootup...
Hi,
I'm trying to update the FW of my nRF9160-DK.
Running MacOs Mojave 19.14.6. Installed nRF Connect 3.3.0. This is the log after startup of nrf connect:
2020-01-24T15...
Hi
I've checked the two PWM examples in SDK, pwm_driver and pwm_library, they seem too complex for me to understand, does anyone know where I can find a simple PWM example...
Your download page for nRF-Command-Line-Tools is not working and it redirects to "page not found (Error 404)". I am using this link https://www.nordicsemi.com/Software-and...
I am currently working on a project where I am checking an input > 3V then passing it to ADC and increasing count based on it. The count value increases or stays the same...
I'm going to write to inquire about Bluetooth Low Energy Device Beacon which will be smallest in size and can operate with coin cell battery and also able to communicate two...
Trying to build the app from C:\Users\xxxx\Documents\SEGGER Embedded Studio for ARM Projects\nRF5SDK160098a08e2\examples\ble_central_and_peripheral\experimental\ble_app_interactive...