Hi,
I'm working on a project where I need to sample an ADC with an accurate sample rate. It essentially works except that I do not get the correct rate from the timer...
Hi,
I’m observing an issue in a Zigbee network where, after several hours of correct operation, the routers stop retransmitting the NWK broadcast frames sent by the coordinator...
Hi,
I am trying to program a custom board containing an nRF9151-LACA using the external programming interface (P20) on an nRF9151 DK. The board has never been programmed...
Hello.
I am currently migrating a project from NCS v3.2.4 to v3.3.1 and transitioning from Partition Manager to devicetree-based partitioning, following the official migration...
Hi,
I’m reviewing the release notes of the Zigbee R23 add‑on , and I see that the compatibility table maps each add‑on version to a specific NCS (nRF Connect SDK) version...
Hi all — I'm developing a custom nRF5340 development board (Raytac MDBT53-1M) and would value the community's honest read on whether it's worth producing.
The goal is...
Hi,
I am using two nRF52833 devices with the nRF5 SDK. They are paired and bonded to each other. Occasionally, I encounter the following error in peer_manager_handler :...
I receive this output from west when trying to build the asset_tracker example from either master or v1.1-branch:
west build -b nrf9160_pca20035ns -- west build: build configuration...
Hi
I am using a buttonless DFU to do OTA for my application. Everything is working fine up to now, but now my custom board got few modifications of using PIN 16 for USB...
I am trying to complie Eddystone project which is part of NRF5 SDK and when i compile the project in Embedded Studio I get the following error
/resized-image/__size/738x210...
Hello. I am developing with the following configuration.
In this configuration, since it is necessary to connect multiple peripherals with multiple roles, "scan_start...
Since migrating to the Zigbee 3.1 SDK I have noticed a few oddities with the behavior of attribute reporting that I am thinking are related to the following bugfix:
The...
HI,
I find that the DFU code start address regsiter is different between SDK15.3 and SDK16
SDK15.3
MemorySegment name="uicr_bootloader_start_address" start="0x00000FF8...
Hi,
I'm using the Home Automation profile of the Zigbee protocol and, in particular, I'm developing the Window Covering Device, present in the SDK "nRF5_SDK_for_Thread_and_Zigbee_v3...
It appears the softdevice gets into a strange state when a BLE connection is lost while transferring data. How does application code reset or reinitialize the softdevice ...
Hello,
On the documentation page for nRF5 SDK for Mesh ( https://www.nordicsemi.com/Software-and-tools/Software/nRF5-SDK-for-Mesh ) it says that only the nRF52832 and nRF52840...
Hello,
I'm seeking some clarification on a few points to determine the performance of the nRF52840 in high density deployments. The current intended soft device is S140...
Hello,
in the current project we use a large array (16kB) in RAM to store data. After a reset we would like to check if the array is not corrupted to continue processing...
Dears,
I'm using nrf52832 with PCA10040 and SDK 16.0.0,I want to make a DFU via uart. So used the firmware provided in the SDK(nRF5_SDK_16.0.0_98a08e2\examples\dfu\secure_dfu_test_images...
Hello,
I would like to evaluate nRF9160 for incoming project.
I have Nordic Thingy:91 with iBasis sim card.
Unfortunately, during configuration it turned out, that...
Hi,
We are using nRF9160 for our application and need to design power supply with battery management IC for it and need to know how much power it will consume with all...
