Hi Nordic DevZone,
We are currently looking at how best to handle nRF9151 programming in mass production, and I would like to understand Nordic’s intended approach a bit...
Hello Nordic team,
What is the image frequency of the nRF54L15 receiver?
We need this information for Bluetooth SIG RF-PHY qualification (RFPHY/RCV/BV-03-C, RFPHY/RCV...
We are developing an application based on the nRF9151 using NCS 3.1.1 and modem firmware mfw_nrf91x1_2.0.3 .
We would like to use Proprietary PSM to control the modem's...
Hello, The nRF9151 hardware design guidelines (power sequence) require VDD_GPIO to be applied at least 6 ms after VDD and ENABLE, after the hardware boot. In our design a...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Dear Team,
I have been running two nRF54LM20-DK as Initiator and Reflector for Bluetooth Channel Sounding.
I adjusted the ranging algorithm RAS_Initiator to print Local...
Hi,
I'm trying to find out how people automate current measurements with the PPK2 beyond doing it by hand in the Power Profiler app.
From the threads here it looks like...
Hi All,
Sanity check here. I'm reading the RSSI value from a received packet
if (nrf_esb_read_rx_payload(&rx_payload) == NRF_SUCCESS) { if (rx_payload.length > 0) {...
A device that is provisioned with PB-GATT enabled stops receiving mesh packets after the provision is complete.
When the provisioning process is complete nrf_mesh_disable...
HI,
I got the following log while advertising:
SOFTDEVICE ASSERTION FAILED AT 0x00014AA6
Since this address locates at softdevice, I can not know what happens.
Would...
Hello,
Using nRF52 DK boards, I'm trying the simple_message_model by modifying the light switch example.
With the client, I simple send a 12 bytes unreliable message by...
Hello! I have a question about nordic thingy 52. Is there any possibility to play more than 8kHz on this board? For example: if i will change speaker on another it could help...
Hello, How do I set the analog reference voltage to external pin P0.02? I'm using the arduino environment so I don't know how to set it via those registers? I'm currently...
Hi,
I am using SDK 15.0 on a custom board using nRF52840. Softdevice is 6.0.0. Coding with SES.
I am investigating and trying to fix the infamous IOS caching of characteristics...
In the schematic of the nRF52840-DK L1 and C4 form the matching network. C22 is noted with NP, but on the DK i have, is a component placed.
Since i would like to use the...
Hi to everyone!
I've been testing the Bluetooth on the nRF52832 DK board with some of the examples and I have saved the mac address (obtained from my smartphone).
In...
Hello All,
I was wondering if someone can confirm the consumption of the nRF52840 in SYSTEM ON when running the Power Management Example on the nRF52840 DK board (in nRF...
My end object is to connect the peripheral to one required central. It should not get connect to another central or to the nRF connect app.
I have gone through many example...
Hi everyone ,
I'm looking for the ULPMark score for the nRF52840.
On the EEMBC website, I 'm seeing that Nordic Semiconductor is a partner, but I don't find any information...
Hi,
we are late stage development on NRF52840 with sdk 15.0 and softdevice 6.0. The mind turns to certification. It all seems very complex and confusing
1) Do we need...
I have an nRF52840 based peripheral running SDK 15.3.
I have a custom service with a write characteristic and a read characteristic. The peripheral supports multiple connections...
As far as I can tell the values are inverted.
4.8.2.2.1.1 Occupancy Attribute
The Occupancy attribute is a bitmap.
Bit 0 specifies the sensed occupancy as follow:...